DIY well insulation for the winter

Making sure your house is adequately insulated as winter approaches is essential for cost and energy savings as well as your comfort. The well or basement is an area that is frequently disregarded, even though many homeowners may concentrate on insulating their walls and attic. In this tutorial, we’ll discuss the value of well insulation and provide you useful do-it-yourself advice on how to successfully ward off the cold.

Why is it so important to insulate your well? You see, your well provides a direct line of entry for cold air to enter the foundation of your house. If you don’t have enough insulation, your HVAC system will have to work harder to keep the cold out, which could result in frozen pipes, cold drafts, and higher heating costs. Insulating your well helps to create a barrier that keeps the temperature inside your house constant, keeping you comfortable and minimizing energy waste.

Let’s now explore how you can approach this do-it-yourself project. Evaluating the insulation condition of your well is the first step. Does the existing structure have any insulation? If yes, does it require reinforcement or replacement, or is it adequate already? Don’t worry if there isn’t any insulation; we’ll walk you through the entire process.

Make sure you have the required supplies before you start. Generally, you’ll need duct tape, gloves, safety goggles, a utility knife, and insulation material like foam board or fiberglass batts. Furthermore, since some insulation materials can release fumes, make sure the space where you’ll be working has enough ventilation.

Now that you have your supplies, it’s time to begin the insulation process. To start, give the well area a thorough cleaning to get rid of any moisture, dirt, or debris that might reduce the insulation’s efficiency. The next step is to measure the well’s dimensions to estimate the amount of insulation material you’ll require. In order to ensure full coverage, it is preferable to have a little bit more than you believe is necessary.

After obtaining your measurements, cut the insulation material so that it fits tightly up against the well’s walls. If foam board is being used, a utility knife can be used to easily trim it to size. Wear safety goggles and gloves when handling fiberglass batts to prevent irritation. Using duct tape or the proper adhesive, firmly attach the insulation, making sure that no spaces remain exposed or gaps exist.

Once the insulation is in place, check your work and make any necessary corrections. Pay special attention to any protrusions that might need more care, as well as corners and seams. After you’re happy with the insulation coverage, you can relax knowing that the winter cold won’t harm your well.

By taking the time to insulate your well, you can improve long-term energy savings and environmental sustainability in addition to improving the comfort of your house during the colder months. You can take on this project with confidence and enjoy a warmer, more energy-efficient home all winter long if you follow these easy DIY tips.

Contents
  1. Which are better to use materials
  2. How to insulate a sewer well
  3. A cover for a well and a wooden house
  4. Entrust the insulation of the PPU well to professionals
  5. Warming of wells for the winter
  6. Polistyle foam for insulation of the well
  7. Warming of wells with a foam
  8. Insolon insulation
  9. Warming with polyurethane foam
  10. Does the well freeze in winter
  11. In what cases is the insulation required
  12. How to warm the well correctly
  13. Insulation with polystyrene
  14. Insulation using isolon
  15. Warming with polyurethane foam
  16. Why and from what water freezes in the well in the well in the well
  17. How to warm a brick well
  18. Insulation of the well for the winter, what to warm and how to do it
  19. Materials used for insulation
  20. Cover insulation
  21. Thermal insulation of the upper ring of the structure
  22. Building a tree made of wood
  23. Why thermal insulation is needed
  24. The best thermal insulators
  25. Why insulate the well, if there is no need in the water in winter
  26. Why is the water in the well of the well covered with ice
  27. Heater for wells
  28. How to insulate a well with polystyrene foam
  29. Why is it necessary?
  30. The main methods of insulation
  31. The main stages of work
  32. Advantages and disadvantages of the material
  33. How to insulate a well
  34. Ways of insulation
  35. War insulation
  36. Polyurethane foam – cheap and reliable
  37. Polistyle foam – the best insulation
  38. Other methods of well -insulation of the well
  39. Why is it impossible to use mineral wool
  40. 2 How to insulate the well cover
  41. 2.1 insulation of concrete well (video)
  42. Is it worth it to be afraid
  43. Self -insulation of the well
  44. How to insulate
  45. Installation of a warm cover
  46. The sequence of work
  47. Decorative house
  48. The order of work
  49. Insulation of the upper ring
  50. The algorithm for the performance of work
  51. Special insulation and polyurethane foam
  52. The order of work
  53. Why insulate the well for the winter
  54. Video on the topic
  55. Warm mini-cesson made of foam pool, which frosts are not terrible
  56. The arrangement of the well, insulate the caisson for the winter, the water will no longer freeze
  57. The simplest and cheap heating of the chip!
  58. The insulation of the well for the winter.
  59. Unusual Cesson insulation for a well. Tested for more than one year. Now I am sure as a result.
  60. Well and well in winter how to warm a well or well for the winter?
  61. Well -insulation of the well, for the winter.

Which are better to use materials

The outcome is contingent upon the accuracy of the insulation selection. Foam is the ideal choice for thermal insulation material. It is possible to prevent the freezing of water in the mine by using this material for warming. It is a thin, soft material that is sensitive to mechanical forces. It is uncommon to use this material for insulation.

Foam or polystyrene foam is the most widely used material. You can even use this material to work independently. Its many years of longevity, high thermal insulation qualities, near total watertightness, low cost, and ease of installation are among its many benefits. The stability of geometry is the absence of foam. It’s important to cut the material so that the pieces are even when warming. It is preferable to seal the joints with foam in order to reduce the areas that are devoid of insulation.

The foam insulation in the well

Polyurethane foam insulation for wells is associated with costly solutions. Beyond the cost, there are a lot of benefits. Maximum tightness is attained, the surface is not deformed or rots, and no prior surface preparation is required. The surface of different kinds of configurations can be heated. Polyurethane foam insulation is nearly impossible to install yourself; you will need to hire experts, which will raise the overall cost of the project.

An inexpensive substitute for polyurethane foam is an insulating shell. It is a two-part design. On concrete rings, they are incredibly simple to install. It is likely possible for you to select the material for your well because there is an enormous variety of pipe diameters and configurations. Foam needs to be used to seal any joints where two halves meet.

If you prefer natural materials, expanded clay, sawdust, and straw might work well.

How to insulate a sewer well

The cesspool needs to be completely sealed in accordance with the most recent building codes. To prevent wastewater from the sewer well from seeping into the ground, the bottom and the concrete walls need to be properly waterproofed. In reality, quite difficult to waterproof cesspools are arranged using a brick, tires, and other materials. However, it is imperative to insulate the cesspool lid for the winter, regardless of the material utilized.

There are a few things you should do in order to properly insulate the sewer with your hands. Priority one for maintaining wastewater heat requires insulation of sewer pipes. To prevent heat loss, the well’s cover and walls should also be treated. Every task is completed with a technology previously mentioned. Additional information about every step of communications thermal insulation can be found in the video at the conclusion of the article.

A cover for a well and a wooden house

Having constructed the insulated cover, you can take the simplest precaution to guarantee that the water in the well doesn’t freeze. It will help the heat of the water to build up and keep ice from forming. It is important to keep in mind that the water’s temperature never drops below 5-7 degrees, even during the winter. By blocking off outside influences, we can so rule out the chance of freezing.

In order to prevent frost damage to the well lid, plywood, mounting foam, and insulation will be needed. Buying high density material is recommended as it will help prevent cracking. Even the tiniest insulation particles won’t fall into the water.

To warm up the hatch, measure twice and cut two plywood shields so that the product’s diameter is two to three centimeters smaller than the well pipe’s diameter. Boards can be fashioned into shields by tightly adjusting them to one another. A film covers the one that will be in closer proximity to the water. Therefore, waterproofing will be done. It’s essential to keep a wooden shield free from rot. Since the primer will come into contact with drinking water, covering the product with one is prohibited.

Polystyrene foam, or an equivalent material, is bonded to the rear of the shield to serve as insulation. A second piece of plywood is used to seal the structure before holes are drilled into it. It must pass through the ventilation pipe.

The wire is fixed on the hatch so that it can be raised or lowered. There are two hooks on the headline that make it simple to hook the wire for them, preventing the hatch from coming into contact with water. The insulated well cover is put in place after the work is finished.

It is necessary to lower the hatch below the soil’s measurement mark. If insulation is not available for purchase, a well can have two shields placed in it. If they are positioned apart, the heat will keep the air space intact.

Although this type of thermal insulation is very dependable, it is not very practical if you are not trying to keep the well open until spring. After all, you will need to continually take off and replace the lid in order to acquire water.

In the event that synthetic materials not covered in this article are chosen for insulation, you must first become familiar with the usage guidelines.

They might, like mineral wool, render the water in a well unfit for human consumption or even hazardous. Use caution and only dependable insulation materials.

Whatever method you decide on, the important thing is that the well is insulated, long-lasting, and provides cool well water for drinking. For the person fleeing the city crane, she is far more agreeable and helpful.

Entrust the insulation of the PPU well to professionals

While it is possible to attempt creating the well insulation on your own, it is advisable to consult with actual experts to address this issue.

Due to its special properties, this heat insulator has been used extensively in many industries worldwide, including those in the polar regions, but it has most recently been used in space. At first glance, the method of creating frost-resistant, heat-insulating protection using polyurethane foam appears to be quite straightforward. Although you can attempt to insulate the well on your own, it is advisable to call in experts to handle this task.

For many years, the business Ecotermix has successfully provided insulation services for wells as well as other residential buildings, and it assures each customer:

  • Operational execution of the application.
  • Individual approach.
  • The implementation of all work is not only fast, but also of high quality.
  • Free consultations on all issues.
  • Ensuring the acceptable cost of services in conjunction with the discount system for regular customers.

Speak with the experts; polyurethane foam effectively retains heat, preventing the well from freezing during the winter.

Your well will last you for many decades if you now promptly safeguard your source of water on the property!

Why is PPU used as insulation from ecotermix instead of another material? Watch the video below to find out:

Warming of wells for the winter

Today, there are several techniques for thermal insulation in use:

Polistyle foam for insulation of the well

Under soil pressure, polystyrene maintains its geometric sizes due to its increased structural stability. It is immune against fungi, mold, and bacteria.

After 25 years, there has been no change in the mechanical and thermal indicators of polystyrene. The sole drawback of using polystyrene for well insulation is its instability when exposed to ultraviolet light. As a result, foil, paint, or oil paint should be used to protect its surface.

DIY insulation method that you can perform yourself:

  • Initially, you should dig a trench with a depth of 1.5 diameter
  • Then a shell from polystyrene is selected according to the diameter of the well
  • Fastening occurs using a "spike-paz"
  • Next, the trench is buried

There is a warming lid atop the well. After cleaning and repairs, the "shell" is taken out and put back in.

Warming of wells with a foam

Penoplex, also known as extruded polystyrene foam, is a highly resilient material that offers superior strength, moisture resistance, and thermal insulation. It is steam-treated, moisture-resistant, mold- and rot-resistant.

Insolon insulation

Since insoloon has a self-adhesive layer and is covered in foil on both sides, insulating a water well with it is a fairly straightforward process.

Warming with polyurethane foam

Prior to using polyurethane foam to insulate the nation’s wells, it is important to understand some of its primary features. If the mixture is used when the street temperature is between 20 and 30 degrees, it will foam more severely. Polyurethane foam doesn’t absorb water, doesn’t emit harmful substances, and doesn’t decay.

The following steps make up the insulation process:

  • Initially, the well is dug around the perimeter to the depth of freezing of the soil.
  • Further, the components of the polyurethane foam, which are located in different containers are heated and, through high pressure, enter the sprayer chamber (mixed)
  • after which all walls are covered with such a solution

The tiny fissures can be filled by polyurethane foam because of its ability to foam and expand in volume. Once it solidifies, a 2-3 cm thick layer of rigid, monolithic heat-insulating material forms.

Polyuertan foam should not be exposed to direct sunlight because it is afraid of UV radiation. To do this, the surface is painted with oil paint, foil, or a crowd.

Does the well freeze in winter

It’s an intriguing question, but our ancestors managed without thermal insulation in some way. And the inevitable query: Does the well need to be insulated?

Indeed, there are multiple reasons why the well freezes.

  • The location of the aquifer is above the depth of freezing of the soil. In this case, the water in the well will freeze, t.To. the soil temperature is transmitted to her. If the water level is lower, then there is no need for insulation;
  • lack of insulation;
  • irrational pipe laying. Water supply, is a system of pipes by which water is supplied to the house. Depending on the depth of their placement, their ability to resist freezing depends. They also need to insulate the place of inserting the pipes into the mine or the establishment to the house;
  • The discoveries of the head. The difference between water in the well and air temperature may exceed 30 ° C. Wooden houses installed on traditional wells prevented direct contact of warm water and cold air. If the house is absent, then the water is covered with an ice crust. And the larger the temperature difference, the thicker the formed crust will be;
  • The use of a well with high thermal conductivity for the construction of a well: brick, concrete rings, monolithic concrete structure.

The final paragraph provides the best natural insulation for the well and explains why our ancestors did not freeze: they were composed of wood.

In what cases is the insulation required

It goes without saying that he does not require any thermal insulation if the well was built in accordance with old customs, which calls for the use of wood. There are some exceptions; the well cover, for instance, requires insulation. In this instance, a second wooden lid must be made and fastened inside the structure. This cover will effectively shield the cottage from:

  1. snow hollows;
  2. temperature differences;
  3. the hit of dry leaves and other garbage.

Almost all wells constructed in the modern era use reinforced concrete rings. These wells have many benefits, including:

  1. strength;
  2. reliability;
  3. durability;
  4. Simplicity of installation and further care.

They do, however, have one major disadvantage: they require insulation in the winter.

Speaking of which, The structure itself won’t freeze if the water within it is situated below the soil’s freezing point. However, if this is the case, insulation must be installed!

Three thermal insulation technologies are available right now:

  1. insulation of the cover cover;
  2. thermal insulation of the upper ring;
  3. Construction of a decorative house.

We will become more familiar with each of the potential approaches.

How to warm the well correctly

The well can be insulated using a variety of techniques and materials; the most widely used ones are listed below.

Insulation with polystyrene

Polystyrene is an extremely common material. To increase, click.

It is noteworthy that polystyrene was used as the well’s insulation material in order to provide independent heat insulation.

Choosing a material in this situation is not too tough because polystyrene products are now available in the direct form of a shell (semicircular).

In addition, a wide variety of polystyrene products with different thicknesses, diameters, and shapes are available in the range.

A trench that is at least 1.5 meters deep is dug out the length of the well’s perimeter before the well is insulated for the winter. After that, the suitable heater shell is chosen and fitted.

The trench is filled in and sealed with the insulated cover once the heat-insulator fasteners are installed using the spike-paz connecting element.

The polystyrene shell is simple to disassemble during well cleaning or repair work and to reassemble in the same location after completion.

The heat-insulating polystyrene is not susceptible to deformation when subjected to soil pressure. A high stable structure determines this attribute.

Additionally resistant to bacterial growth, the growth of mold, and fungal formations is polystyrene. For 25 years, this material’s mechanical and thermal insulation qualities remain unchanged.

The sole drawback of polystyrene is its poor UV resistance.

The insulation’s surface is sealed with foil, toly, or an oil paint layer to keep the sun out.

Insulation using isolon

This insulation technique is very easy to use. An isolon ison, which has a self-adhesive layer on one hand and foil on the other, is used for thermal insulation.

Warming with polyurethane foam

Insulating the water supply well with polyurethane foam is the next step towards creating thermal insulation that protects the well from frost. Owing to its special properties, this heat insulator finds extensive application in space and in polar environments.

Insulation made of polyurethane foam is impervious to moisture absorption, harmful substance secretion, and deterioration.

Mice won’t ever start in it, which is crucial in rural areas.

The temperature of the components and atmosphere should stay within the range of +20 to +30 degrees while the well is being warmed.

If not, there will be issues when making the heat-insulating mixture; the foaming will be significantly worse, and more insulation material will need to be used.

Digging up the surrounding soil to the freezing point is the first step in this process. In this instance, there is no need to prepare the concrete surface.

The components of the polyurethane mixture foam, which are packaged in separate tanks, are heated to the specified temperature before the water supply well is insulated. The parts are put inside the pistol-spray chamber under intense pressure.

Create a mixture in this chamber by mixing it and applying it in a uniform layer to the well’s walls.

All of the wall’s cracks and other flaws are filled in during the polyurethane application process, which foams the foam. A three-centimeter layer that is both solid and heat-protective forms when it solidifies.

It is covered in foil or nothing at all to shield it from UV light. Additionally, oil paint can be used to coat thermal insulation.

Why and from what water freezes in the well in the well in the well

Those who live in the middle strip, where the ground can freeze up to three or four meters below the surface during the winter, must ensure that their well is properly insulated.

First off, a lot relies on the materials that were utilized to build the well. You won’t have to worry about ice forming inside of it if it’s made of wood, which is extremely uncommon these days. Wooden wells have long been a source of water for our ancestors’ domestic needs, even during the harshest winters.

However, the reinforced concrete that has been used in recent decades and is still being used to build wells has the potential to quickly deplete your water supply in the event of certain coincidental circumstances. This is because the freezing of water in a structure like a well without insulation is a given. The truth is that water expands when it freezes, which can damage materials like reinforced concrete. If an ice cork forms at the intersection, it may even cause the rings to move, which could have very dangerous repercussions.

Second, a lot is dependent on the well’s water level. This is particularly true in swampy areas where the water is between one and two meters below the surface, or "a stone’s throw" away. The chance of an ice shell is very high in these situations.

Thirdly, the depth at which the soil freezes is a critical factor. You don’t need to be concerned about the well freezing in the southern regions, where the Earth freezes at a depth of only 1.5 meters. However, residents of the middle strip, where the soil can freeze to a depth of three or four meters during the winter, must worry about well insulation, and it is best to make the decision as soon as possible.

How to warm a brick well

Using the same techniques as for concrete wall rings, isolate the pre-existing brick well. And quite another matter if the building is only getting started.

Next, during the work, the brickwork’s insulation and waterproofing are completed:

  • The barrel of the well does not have to be round, it can have both a square or rectangular shape. In this case, well masonry with insulation is the most suitable option. This is a very popular building in the construction of the houses: the brick is laid so that empty wells are formed in their thickness, which are filled with sawdust, expanded clay, polystyrene crumbs, or filled with foamyizol.

The brick wall’s insulation

  • In another version, they build two parallel, stiffly interconnected walls of the walls, the space between which is also filled. The colodeous layer with insulation is very convenient for arranging a tank in a finished pit. It can be a drinking water intake up to six meters deep, and any other type of well: surfaced, rotary, observation.
  • Of course, the well does not require such wall thickness as for the building – a half brick is enough. After the masonry work is completed, it remains only to plaster the wall outside and make a drainage sleeve. If the plasticizer, strength and waterproofing of the elevated walls will be provided to the masonry and waterproofing solution, will be provided with the maximum.

Building a house, or canopy, over a drinking well is a good idea to keep it from dozing off during the winter months when there is snow on it. Regarding the cover, a multi-layered wooden one is preferable.

Insulation of the well for the winter, what to warm and how to do it

Water supply and all associated questions are perennially relevant. This is particularly valid for rural regions. Wells need to be properly insulated during the winter because they have a chance of freezing. Before the onset of cold weather, it must be completed in accordance with the set rules.

Materials used for insulation

You can use the widest variety of insulation materials for insulation. You shouldn’t worry about isolation if the well is made of wood because it is not required. Sometimes it’s just the lid that’s insulated.

It offers defense against the subsequent elements:

  • snow fall;
  • temperature changes;
  • Prevention of leaves.

The majority of reinforced concrete wells installed today are different in that they are stronger, easier to maintain, more reliable, and durable. However, in this instance, it’s imperative to maintain the well’s insulation for the winter.

Typically, the following insulation technologies are employed:

  • lid insulation;
  • insulation of rings;
  • Establishing a decorative house.

Cover insulation

Well-winterized and insulated

In November, you can finish insulating the well for the winter by yourself. You should take care of the lid first. Since all you have to do is create an extra cover for the inside of the structure, this is fairly easy.

The following supplies are required for this:

  1. plywood;
  2. wire;
  3. glue;
  4. Styrofoam;
  5. plastic pipe;
  6. Mounting foam.

Two plywood circles with corresponding lid diameters are cut out. Two holes will need to be made: one for the hose and one for ventilation. Their maximum distance should be six centimeters. The best way to do them is with one hand. Depending on the second circle’s diameter, four tiny wire holes are made.

Make sure to use the prepared foam to cut the third circle to the same size. It must be adhered to the bottom circle using glue.

Foam installation is required to insulate the formed joints. The wire is used to create a unique ring. To do this, a circle is fixed and the first workpiece is wrapped.

Thermal insulation of the upper ring of the structure

Thermal insulation of the well’s upper ring is required to fully warm it for the winter. You can use foam or polystyrene for this.

On the exterior, where a specific amount of land is removed, will be the insulation. Installing foam forces educated joints of insulation into place. The surface is then painted and plastered. Subsequently, earth is once more placed over the pit.

Building a tree made of wood

The video below will be a useful tool if you want to see how to warm the well using your hands.

The upper ring has a film covering it from the inside. A number of foam rectangles are cut out. Aluminum wire is used to fix them.

The house is a lovely and cozy option.

Small logs of logs can be constructed. The best shape to use is hexagonal; a multi-layered roof is built on top of the house. The design may be aesthetically pleasing but also challenging to use.

The process of insulating the sewer well for the winter is comparable to pouring a drink. The freezing point is assessed. You cannot insulate it if there are no issues even during extremely cold frosts. In the unlikely event that the water is frozen, you must wait for it to thaw before adding insulation.

The majority of the time, thermal insulation is employed, which causes the water to melt. Another way to reheat the pipeline is with a construction hair dryer; however, insulation is required to restore waterproofing.

We hope you found the information useful. We would be appreciative if you posted it on social media.

  • Water pressure for the washing machine automaton
  • Agidel pump characteristics
  • Is it possible to drill a well under the water inside the house
  • Rain plum
  • Industrial drains
  • How to clean the shower at home
  • Spent on how to write correctly
  • Installation of a well
  • Water ozonation in the pool
  • Hot water counter how to stop

Why thermal insulation is needed

Generally speaking, wells that rural residents regularly use are insulated even while they are being built. However, designs that are used primarily in the spring and summer, that is, in the summer, are frequently constructed without a layer of thermal insulation. There could be several very unpleasant outcomes from this:

This is the process by which wells open.

  1. The water in the depths of the well begins to freeze much later than the air temperature drops below zero. As a rule, the first signs of the formation of ice traffic jam appear at a temperature of -15 … -200s. Moreover, the higher the water level in the well, the faster it will freeze.

Because snow on the ground acts as a reasonably good heat insulator, freezing will occur much more intensely during the Hismless winter.

  1. The most obvious problem caused by the formation of an ice traffic jam is the inability to collect water. Even a layer of ice in two to three centimeters can become a problem, since it will not work to break through it with a bucket.
  2. Another unpleasant feature of ice is its increase in volume. When expanding, the ice traffic jam presses on the walls of the well, and if it enters the joint of concrete rings, then they diverge to the sides, and if the formation of cracks is not excluded to the whole area.

In addition to obstructing access to water, the ice traffic jam contributes to wall destruction.

  1. The formation of ice also harms equipment: freezing can disable the pump or provoke cracking of hoses. It is for this reason that the water meters in wells and caissons are necessarily underwear – the exposure to low temperatures on quite delicate meter mechanisms is almost guaranteed to reduce their accuracy.
  2. Finally, an ice plate with a thickness of 10 cm or more during the thaw can fall into the water, damaging the equipment located there. I also know the case when an ice block formed after two weeks of frosts under -250s was cut off with its weight, a rather strong cable, on which the pump was held.

Equipment for measuring and pumping must also be insulated.

Generally speaking, there are sufficient reasons to support high-quality well thermal insulation, particularly concrete. Therefore, it appears to me that investing a little time and effort now can help prevent more significant issues down the road!

Comfort and energy efficiency during the winter months depend on keeping your house warm. By insulating your well, you can keep it from freezing and guarantee a steady flow of water during the winter. With the correct tools and materials, DIY well insulation is an affordable solution that’s simple to put into practice. You can minimize heat loss, lower the chance of pipe damage, and save money on energy bills by properly insulating your well. This post will walk you through the process of insulating your well, offering helpful advice and detailed instructions to ensure you complete the task successfully.

The best thermal insulators

Foam. One type of artificial material is heat-insulating foam made of extruded polystyrene. It is appropriate for the lining of well mines because he is not afraid of moisture or mechanical exposure. Because of the material’s high vapor permeability, condensate cannot build up on the well’s interior walls.

The selection of heat-insulating materials is an important consideration in the insulation of sources. Budget-friendly thermal insulators with good technical qualities fall into this category. PENOPLEX

One type of artificial material is heat-insulating foam made of extruded polystyrene. It is appropriate for the lining of well mines because he is not afraid of moisture or mechanical exposure. Because of the material’s high vapor permeability, condensate cannot build up on the well’s interior walls;

Isolon. In a well mine, heat loss is prevented by covering the exterior of a self-adhesive heat insulator with foil. It can be applied nationwide for source covers, basements, and ring wurr insulation. It is resistant to rust and deterioration because a thin plastic film covers the foil’s exterior;

Foam of poliuretan. You must be able to apply liquid heat insulators correctly. To accomplish this, apply a stream of the heat-insulating mixture to the well’s exterior walls using a specialized spray gun. Because of its low heat conductivity, the monolithic coating completely prevents the source’s water from freezing;

Polystyrene foam. The half rings that symbolize this kind of thermo-insulating material have a "lock" connection mechanism. Polystyrene foam is a convenient material to shell the well’s walls because it can be easily disassembled and reassembled if needed.

  • Foam . Artificial material is one of the extruded polystyrene heat -insulator foam. He is not afraid of moisture and mechanical exposure, therefore it is suitable for lining of well mines. The material has high vapor permeability, so it prevents the accumulation of condensate on the internal walls of the well;
  • Isolon . A self -adhesive heat insulator on the outside is covered with foil, which prevents heat loss in a well mine. It can be used in the country for insulation of the wart of the rings, basement and the source cover. It is not subject to corrosion and decay, since on the outer side of the foil is covered with thin plastic film;
  • Poliuretan foam . Liquid heat insulator that you need to be able to apply correctly. To do this, use a special spray gun, from which the outer walls of the well are treated with a stream of the heat -insulating mixture. The monolithic coating has low thermal conductivity, so it perfectly protects the source and water in it from freezing;
  • Foam polystyrene . This type of thermo -insulating material is represented by half rings, which have a “lock” connection system. It is convenient to shell the walls of the well with polystyrene foam, because if necessary, it can be dismantled and used again.

Why insulate the well, if there is no need in the water in winter

A country house owner needs to be aware of how damaging the water supply system is to the recurring cycle of freezing and thawing. The buildings eventually collapse due to their progressive destruction.

Crucial! Multiple cycles of freezing and melting can cause damage to the water supply. The volume of water is greater in a solid aggregate state.

The rings start to collapse because of the negative effects of its expansion. The well will be completely useless in a few seasons. In addition, the expense of fixing it will be similar to that of installing a new one.

The volume of water is greater in a solid aggregate state. The rings start to collapse because of the negative effects of its expansion. The well will be completely useless in a few seasons. In addition, the expense of fixing it will be similar to that of installing a new one.

Should the well consist of concrete constructions, they will move in relation to one another during freezing and thawing. There is a seam break in this instance. The home’s communications are cut off. Furthermore, the insert’s integrity can be compromised. This is all accompanied. When the soil thaws in the spring, it is particularly apparent.

Crucial! The cost of restoring the well will be high, and repairs will require a significant time and labor investment. The house’s occupants will be without water for an extended amount of time.

Taking into account everything mentioned above, it is evident that it is preferable to invest the least amount of time and money required to purchase a heater and permanently resolve the current issue.

Having insulated the well once, you will be sure that it will not become unusable for a long time, and the water in it will be all year round.

Why is the water in the well of the well covered with ice

It is important to note right away that everything is dependent upon the product upon which the well is constructed. Let’s travel back a few centuries at least to the time of the wooden wells. Yes, allow it to grow easily; the mucus-covered walls rot the plant, but in the wooden mines, the water never freezes in the winter. This is because wood has good thermal insulation, something that reinforced concrete cannot claim.

Additionally based on the volume of water in the well. In the winter, all that will be visible instead of water is the lovely glow of ice if the land is densely populated with subsurface waters that flow nearly to the surface. However, the likelihood of an unpleasant surprise increases if the water is deep—deeper than five meters.

It is important to take into account the location of the residence, specifically the soil’s capacity to freeze in the winter. The thermal insulation then became a grumpy joke.

If this is a chernozem, the well is unlikely to freeze—even in a ring of reinforced concrete. However, if you live in the north, where the soil freezes more deeply and strongly, you might reasonably conclude otherwise. In the second scenario, it is preferable to create insulation right away, learn how to construct a well of the well, and save money on the quantity of nerve cells as well as the well itself for later.

Heater for wells

Deep wells and private wells are used to supply suburban real estate with independent water supplies. Particularly for those with a lot of surface water, the functioning of the structures mentioned was established during the winter. In this instance, the fluid’s upper layer frequently freezes, and after multiple cycles of freezing and thawing, the concrete rings are destroyed. Purchase a well heater to prevent this from happening; you can do this on our website or at any construction supply store.

It is advised to use a heater for the well made of foam in the winter to guarantee non-precise operation of the water tank. The truth is that this material does not fear moisture, in contrast to mineral wool, and it continues to function flawlessly even when water seeps through. There are various stages to the insulation process itself:

  • Thermal insulation of the well cover. Simple procedure that implies foam attachment to the damper. In this case, the insulation is laid between two layers of protective material, such as metal or a wood processed from decay;
  • insulation of concrete casing rings.

The concrete rings’ thermal insulation needs special consideration. The first step in this work is to dig trenches around the well.

In a specific area, you must dig a pit deeper than the soil’s freezing point. By taking these precautions, the building will be shielded from potential freezing and further damage.

Selecting thermal insulation for our tank is now necessary. Mineral wool is not suitable for this purpose, as we have stated previously. This material is formed into plates that require a specific layer in order to be joined. Basalt wool also has a moisture phobia.

Experts say that polystyrene insulation for the shell’s well is the best option for this purpose. When compared to their equivalents, the products mentioned have several advantages:

  • Polistyle materials are made in factories in the form of a half -swing, which are reliably fixed with each other using a castle system, which avoids cold bridges;
  • The second advantage of foam products is considered minimal thermal conductivity, as well as the lack of water absorption.

It is fairly simple to insulate the structure using half rings. The well’s surface, which ought to have good indicators of water and frost resistance, is first coated with glue before the half rings are secured. An umbrella dowel of nails is used to finalize the fixing of the insulation. These nails are screwed into the concrete multiple times.

The well’s heat insulation keeps it from freezing during the winter. The best method for warming the well is with this technology.

Thermal insulation for the well in size can always be ordered!

To accomplish this, please give us a call at 84956457039 or send an email to mail@tepo-max.ru, and we will estimate the price.

How to insulate a well with polystyrene foam

The well is occasionally the only source of clean water for the majority of summer residents. They attempt to look after him because of this. People try to warm the well on the eve of the cold for the same reason.

Why is it necessary?

To some, the words "well insulation" may seem a little odd. Why, in fact, does the well need to be insulated?

Some owners will argue that there is no need for water because they don’t use the cottage during the winter. Therefore, don’t bother yourself or the well insulation.

This viewpoint has very tragic repercussions: in the unlikely event that the well’s water freezes, there could be a displacement of concrete rings, leaks (in which case a hydraulic fiber would need to be made), and other issues of a similar nature. Furthermore, eliminating them will take a lot more resources and work than just warming the well. As a result, you ought to consider.

To be fair, it should be mentioned that sometimes, even during the worst frosts, the water in the well doesn’t freeze. However, this is only feasible if the water is 8–10 meters below the surface or if the well is entirely constructed of wood.

The main methods of insulation

The well can be heated in a few different ways:

  • make a lid;
  • insulate the upper ring with foam polysterol;
  • Install a decorative house above the well.

Let’s take a closer look at the polystyrene foam insulation used in the well.

The main stages of work

A clay castle is a necessary component in the process of warming a well. Some proprietors succeed even up to the point of drilling a well.

Only the portion of the concrete ring that rises above the ground needs to be warmed because the water is shielded from freezing by the thick layer of clay.

However, you will need to invest a little more strength in insulation if there is no clay lock.

Examine the primary workflow:

  1. It is necessary to dig a small pit around the well, 1.5 m deep (freezing level), about 50 cm wide.
  2. Clean the surface of the ring from the earth sticking to it as much as possible.
  3. Install the insulation. You can use the polystyrene foam to the shell – it is easily fixed, thanks to special mounts, it has excellent characteristics. If you plan to insulate the wells with a foam, the blocks are simply fixed on the ring, and the cracks between them are thoroughly blended with mounting foam.
  4. After the fixation of the insulation (both on the underground part of the rings and on the above -ground) ended, it should be covered with a layer of plaster. In order not to be wetted in the future, after drying it should be covered with paint.

Important: paint and polystarol foamy must be applied since they shield the material from the sun’s rays. Benefits and drawbacks of the content

Advantages and disadvantages of the material

Why do experts advise using polysterol to insulate wells? The solution is very easy to understand.

This material offers a great deal of benefits.

  • It is resistant to temperature changes;
  • has an affordable cost;
  • easy to install;
  • long service life;
  • resistance to mold, fungus;
  • not deformed under the pressure of the earth.

The "fear" of sunlight that polystyrene foam has is its lone disadvantage. The material’s ability to retain heat is greatly diminished by ultraviolet light, so plaster and paint should be applied to it.

Conclusion

Warming the deck with your hands is an easy task that you can accomplish on your own. It does not call for any specialized equipment or knowledge.

You can be certain that the water in your well won’t freeze, even during the worst frosts, if you just put in a little effort.

We hope you found the article to be helpful. If you spread the word about it to your friends on social media, we would be appreciative. These buttons are located slightly below.

How to insulate a well

Recall! Major repairs may be necessary for an inadequate well following the first winter.

People who live in villages, country homes, or country houses full-time typically install a house on top of another house, which serves a more decorative purpose, or a lid, which is at least a form of thermal insulation for their wells.

Naturally, practically anyone can afford to build the house above the well of a wooden log house because the wood retains heat well or to manufacture the insulated cover. However! In order to ensure year-round operation or a notable prolongation of the life of your water supply, the well needs to be insulated with far greater care.

Recall! After the first winter, the unscarried well might need significant repairs, and the material costs involved would be on par with building a new well! If there is damaged pumping equipment in the well, add it here. It will need to be replaced or repaired entirely.

Ways of insulation

Insulation is available for purchase in nearly all construction supply stores. It is noteworthy how diverse the selection of these building materials is.

Warming can be done with contemporary materials like polystyrene foam or by following centuries-old customs and using wood. What matters most is that the process of supplying water never stops. Examine each of the options listed below in detail to determine which insulation method is best for you.

There are differences between the following techniques for installing insulation:

  1. Insulation from the outside. In this case, all parts of the structure that are above the soil level are subject to insulation.
  2. Insulation of the inside of the well. This method is suitable only to protect technological structures. If we are talking about a water supply, you can install a hatch.

The climate zone should be considered when choosing insulation materials.

War insulation

Wood is a great material for thermal insulation. Regretfully, there is a way out for those who just do not have enough money to completely lay the shaft with a log well. To make it complete, a house must be constructed around the well. In addition to providing the water with ideal freezing protection, such a structure will also improve the site’s landscape design.

A site for the well must be prepared beforehand to prevent the cold from entering the house. There are various methods for doing this:

  • build an air cushion;
  • make a blind area;
  • pour crushed stone or expanded clay.

This method of solving the problem comes at a low cost. The required building materials are within the financial reach of every private home owner. You won’t have to speculate as to whether or not water freezes if you take the necessary steps to warm the mine with wood.

Polyurethane foam – cheap and reliable

Although this material is quite expensive, it will dependable shield the well from frost. A sealed cladding will be able to be made with insulation’s assistance.

Even after several years of use, polyurethane foam does not deform and does not decay. The surface doesn’t need to be further prepared before installation. They can shield couplings and the location of pipe insertion from freezing.

While polystyrene foam has many of the same benefits as polyurethane, polyurethane is not as easily damaged by rodents as polystyrene is. It should be noted that the paint on the rings above the ground needs to be updated once a year.

Polistyle foam – the best insulation

This is a reasonably priced, in-demand material. Polistyle foam consistently keeps the structure safe from frost and does not miss moisture. It stands out for having an extended service life and being simple to install.

The fear of UV radiation is a major drawback for this thermal insulation material. He quickly becomes useless in the sun. Resolving this issue is very easy: painting the exterior of the building is required. Foil, roofing material, and other comparable materials can be used to wrap it.

Sheet insulation is produced by manufacturers. They are cut into ribbons and affixed to concrete structures prior to use. Mounting foam fills the void between the ribbons.

Other methods of well -insulation of the well

There is a large selection of insulation. The construction stores carry foams. This is a foil material, but because it cannot withstand mechanical loads, it is not frequently used to protect wells.

Additionally, a unique shell that can be used to shield the pipe is available for purchase. It will take the place of the sprayed polyurethane foam if funds are tight. The shell is simple to install on the well’s concrete rings and is made of two parts. Because of the variations in configuration, selecting a product that takes the pipe diameter into consideration is simple.

Once the shell’s halves are secured to the pipe, foam is blown into the joints. Consequently, a sealed design shall be produced.

Why is it impossible to use mineral wool

Fiberglass and mineral wool are not good choices for shielding the well from freezing temperatures because they can release insulating particles into the water that renders the well unusable.

2 How to insulate the well cover

Making the most basic sandwich lins out of two pieces of plywood is the simplest option. Pay attention to the well’s interior dimensions when cutting the lid.

As the cover needs to be carefully adjusted, cutting in this area requires a high degree of accuracy.

There shouldn’t be any tiny fissures that allow chilly air to enter. You must add a layer of polystyrene or polyurethane foam in the void created by the separation of two layers of plywood. This will drastically lower the cover’s herming indicator.

To enhance the current thermal insulation properties, you must install the two suggested covers.

One installation needs to be done one meter below the surface, and the second one can be put at the well’s mouth.

It is crucial not to overlook the ventilation, as a tube with a small diameter can be drawn through pre-made holes using two covers.

The well’s insulation is made of wood.

Make sure it doesn’t come into contact with the water’s surface. In order to enhance the well’s aesthetic appeal and thermal protection efficiency, the final step involves building a decorative log house.

It’s neat to concentrate on insulation technology when building a log home, so it makes sense to place jute between the crowns. This organic substance will greatly improve the structure’s thermal insulation qualities.

2.1 insulation of concrete well (video)

Is it worth it to be afraid

Wells serve more than one purpose in terms of functionality. Some are used as the head of a well, where a pump with an injector is installed, and others are where the main water supply units are located. Certain ones were designed with septic tanks or cesspools in mind. They might all require insulation, so keep an eye out for instances like these:

  • The depth of the pipeline. If pumping equipment is installed in the well and there is a supply to the house, then it is worth measured at what depth it is located. If its position is higher than freezing of the soil or at its level, then the freezing of water in the well is possible and insulation is required.
  • There is no well cover. This can lead to snow inward, which will lead to a deterioration in water quality. In addition, constant heat transfer can lead to freezing if the depth of the well is not too large. Therefore, the well insulation is required.
  • The small depth of the well. Water mirror can be at a level of 5 and 8 meters. In this case, there is nothing to worry about. But if the water in the well rises to 2 meters from the surface, then it is worth carrying out work on insulation of the well.
  • Herring water input well-seeptic is above freezing soil. Insulation is required not only for the well, but also the pipes themselves.
  • Concrete rings. At large minus temperatures, concrete rings of the well can act as a thermal conductor, due to which the water in the well may freeze.
  • There is no head of a well of sufficient height. Cold air enters the mine faster, so its construction and insulation are required.

One region’s winter is not the same as another’s. They are soft somewhere, and experience tells us that bad things don’t always happen. However, things can change quickly, so having the well insulated is always a good idea. There are moments when the well’s river flows so quickly that there isn’t time for any frost to form. If nothing has changed in the last few years, insulation might not be necessary.

If the well is in a country house or in a country house where you are not in winter, this does not mean that it does not need insulation. The fact is that when freezing, the water expands and can harm the mine. Often this leads to a displacement of the rings of the well or their destruction. And replacing the lower rings requires great effort. In such conditions, the seams lose their tightness faster, which means that they will have to be constantly maintained, and accordingly, clean the well. The intention to make insulation is very good, it remains only to figure out the materials that can be carried out.

Self -insulation of the well

The complexity of the work will vary based on the insulation method selected. Think about each of them in turn.

1. Building a log home out of wood.

  • Before starting to warm the well with your own hands, you need to lay the foundation around the rings to a depth of at least 50 cm.
  • Then the crowbar crowns are laid, a layer of felt for isolation of joints.
  • The gap between the well and the strapping is filled with insulation.
  • In the end – the construction of the rest of the structure, wood processing and decorative finish.

2. The insulated cover’s production.

  • It is cut out of thick fiberboard or collected from a shawks two round shields. The diameter is selected based on the accuracy of the penalty mine. In the case of concrete rings, it should be 30-50 mm less than the size of the opening.
  • Waterproofing is strengthened on the bottom of the first cover.
  • A layer of non -packed material is laid on top, such as extruded polystyrene foam or polystyrene. The thickness of the latter should be 8-10 cm, for EPS 3-5 cm is enough.
  • On the upper plane of the second shield, two anchor bolts with a ring at the diametrically opposite ends of the circle are attached, for which the cover of the well will subsequently stretch.
  • On top the system is covered with a second shield. If insufficient thickness is used, it is fixed at a distance of 3-5 cm from foam. Air layer will play the role of additional insulation.
  • Inside the well at a depth below the level of freezing of the soil, the mounts are installed on which the lid will lean.
  • Before frosts, the design using ropes is installed in its place.

3. Use polystyrene foam for insulation.

  • Before starting insulation of the body of the well by polystyrene, you need to dig a hole around it to a depth below the level of freezing of the soil.
  • If you use special round slabs, they simply need to be combined with each other using the “Ship-Paz” connection.
  • When laying several rows or in the case of a simple foam with cut edges, the joints between them are glued with rubber -based or butter. If the mounting foam is used, make sure that it does not push the pieces of isolation.
  • After that, the pit is falling asleep and finishing is performed.

4. Using polyurethane foam for warmth.

  • Before insulation of the mine of the well, they dig a trench around it.
  • Next, insulation is carried out to the surface of the rings.
  • After solidifying the material, it can be instilled, apply a protective layer and perform a decorative finish.

Significant details:

  • Water insulation of water supply from a well or well is carried out using a foam shell, but this can not be done if they are laid below the level of freezing of the soil.
  • All polymers are destroyed under the influence of ultraviolet radiation, so the surface needs protective coating. In its quality, oil paint, plaster and other types of finishes are suitable.
  • Work on insulation with polyurethane foam is carried out at air temperature from 20 to 30 degrees of heat. Otherwise, the material will be poorly foamed, which will lead to an increase in its consumption. The components before mixing must also be additionally warmed up.
  • When spraying, the surface of the rings is pre -washed with water from dirt.
  • All polymers maintain contact with a humid environment very well, so moisture insulation is not required.

Methods for fastening the foamyplex to the home’s walls

The low temperature in modern homes is one of their issues.

Evaluation of the "Telpny Paul" heating system: perspectives and apparatus

The room’s heat is distributed unevenly by standard radiators and pipes.

With the exception of a typical heating system, to guarantee adequate heating at home.

How to insulate

There are many different insulation options available, and with the right care and attention, each one can function on its own. However there are just five insulation techniques that are widely used.

Installation of a warm cover

This approach is beneficial due to its superior thermal insulation as well as its capacity to shield the well shaft from stray debris (such as leaves that have fallen from trees).

  • plywood sheet;
  • foam (5 cm of thickness);
  • glue;
  • mounting foam;
  • a piece of plastic pipe for the arrangement of ventilation (it is necessary to prevent the appearance of an unpleasant odor near the water).

The sequence of work

  1. Two circles are cut out of plywood equal in diameter with well rings (along with the walls).
  2. A circle of foam is glued between plywood circles.
  3. For ventilation, a hole is drilled with a diameter of not more than 6 centimeters, into which the prepared wrapping of a plastic pipe is inserted. The tightness of the pipe fit is ensured using mounting foam.
  4. With the help of the wire, the cap rims are performed, and hooks are attached to it to install the insulation at the well of the well (the wire passes through the lower plywood – small holes are drilled there).

Once completed, the cover should be lowered all the way to the ground inside the mine.

Decorative house

A wooden house provides reasonably good insulation in addition to being a lovely decorative element for the courtyard. Many refer to it as a log house.

  • wooden logs;
  • crushed stone and cement (used for the construction of the blind area);
  • Mineral wool as a heater;
  • Tiles on the roof.

The order of work

  1. A blind area is arranged around the mine – crushed stone is compacted and cemented. If desired, you can put tiles on top.
  2. The log house is mounted on the resulting basis. At this stage, the help of specialists may be needed!
  3. The gaps between the house and the ring protruding above the surface are closed with mineral wool.
  4. The roof is made by gable.
  5. After that the logs of the log house must be treated with a special impregnation to ensure protection against moisture.
  6. The log house is closed with a warm lid.

Insulation of the upper ring

A fur coat is an easy and reliable way to stay warm in the winter.

  • polystyrene foam or polystyrene shells (this building material has grooves for dense
  • fixing the entire structure);
  • wood or plywood to create a protective box.

The algorithm for the performance of work

Around the first ring, a small trench with a maximum depth of 1.5 meters breaks out. It is the owner’s responsibility to allow unrestricted access to the ring throughout its height.

Thermal insulation material is mounted around the ring. If this is foam, it can be attached using regular wire that has been wrapped around the ring multiple times and has mounting foam blowing through the cracks.

Sand covers the trench up to the ground, and a wooden box protects the insulation material above ground. If the polystyrene is to be used as a heater, it must be painted or covered with foil because ultraviolet light is dangerous. The installation of the insulation on the warm cover shaft marks the end of the insulation.

Special insulation and polyurethane foam

These insulation types are used because they are quick and inexpensive to install.

  • rolled type of insulation (for example, based from foil);
  • Installation gun, if planned to apply a polyurethane mixture.

The order of work

  1. Digging a trench up to 1.5 meters deep.
  2. The first ring using roller insulation is insulated. If the polyurethane mixture is treated, it is necessary to adhere to the temperature regime. Optimum temperature about +20 degrees. Under such conditions, the material quickly dries (applied with an uniform layer with a thickness of at least 3 centimeters).
  3. The trench falls asleep. The insulation remaining on the surface is covered with paint or foil.
  4. Be sure to mount the lid!

Note that in any case, a warm cover is required. However, the protection won’t be as effective if the mine’s upper ring isn’t insulated.

Why insulate the well for the winter

The well’s water may freeze if any of the aforementioned circumstances exist, so insulation work must be done to keep the water supply operating at its best and avoid causing issues with the water fence.

Even though a country house well is typically only used during the warm season, it is still necessary to warm the well. As a result, you must consider and get ready your work materials.

This is crucial because water that freezes and thaws can cause a structure to gradually collapse.

Application of insulating material to the septic tank walls.

In the event that a well of concrete rings is present, the tightness and integrity of the structure may be compromised due to joint rupture and displacement. There may be cliffs in the pipeline itself and in areas where the pipes collide. The sagging of the soil surrounding the well is proof that there were infractions. It goes without saying that the cost of the repairs necessary to maintain the integrity of the building is high, they involve a lot of physical labor, and they will leave the homeowners without water for an extended amount of time.

For this reason, you only need to decide how best to complete the task and what materials to use, rather than considering whether it is necessary to complete it at all.

Materials Needed: Steps to Follow:
1. Insulation foam boards 1. Measure the diameter of your well.
2. Waterproofing membrane 2. Cut the insulation foam boards to fit around the well.
3. Adhesive or sealant 3. Apply adhesive or sealant to the back of the foam boards.
4. Insulation wrap or blanket 4. Stick the foam boards to the sides of the well.
5. Tape measure 5. Wrap the waterproofing membrane around the foam boards.
6. Secure the membrane in place with tape or adhesive.
7. Cover the entire insulation with insulation wrap or blanket.
8. Make sure there are no gaps or exposed areas.
9. Your well is now insulated and ready for winter!

Keeping your home’s heating system reliable and effective during the winter months requires that your well be adequately insulated. You can avoid freezing, lower your energy expenses, and increase the equipment’s lifespan by taking the time to insulate your well.

The affordability of do-it-yourself well insulation is one of its main advantages. You can make a big, cost-effective improvement to the efficiency of your heating system by using inexpensive materials and simple tools. The initial cost of insulation materials is frequently offset by the long-term energy bill savings, regardless of whether you choose heat tape, foam insulation, or a combination of techniques.

Additionally, DIY well insulation is customizable to meet your unique requirements and tastes. You are free to select the insulation materials that best suit your needs in terms of setup, climate, and cost. Gaining practical experience with insulation also helps you understand your heating system better and how to maintain it.

Do-it-yourself well insulation can help create a more sustainable home environment when done correctly. You can lower your carbon footprint and save money by decreasing heat loss and energy consumption. One simple but effective way to make your home more energy-efficient and to support environmental conservation efforts is to insulate your well.

In conclusion, insulating your well for the winter is a do-it-yourself project that has many advantages, such as reduced costs, increased customization, and sustainability for the environment. In addition to ensuring a warmer, cozier home, you can lessen your energy use and environmental effect by taking the time to properly insulate your well. Thus, prepare to enjoy a well-insulated home this winter by rolling up your sleeves and gathering your supplies!

Video on the topic

Warm mini-cesson made of foam pool, which frosts are not terrible

The arrangement of the well, insulate the caisson for the winter, the water will no longer freeze

The simplest and cheap heating of the chip!

The insulation of the well for the winter.

Unusual Cesson insulation for a well. Tested for more than one year. Now I am sure as a result.

Well and well in winter how to warm a well or well for the winter?

Well -insulation of the well, for the winter.

What type of heating you would like to have in your home?
Share to friends
Michael Kuznetsov

I love to create beauty and comfort with my own hands. In my articles I share tips on warming the house and repairing with my own hands.

Rate author
vDomTeplo.com
Add a comment