Replacing pipes in the bathroom – stages of work by steps from A to Z

Few things are as important for maintaining a home as the plumbing system. Pipes are essential for maintaining a smooth water flow for many daily tasks, particularly in the bathroom. But these pipes could break down over time, resulting in leaks, clogs, or other problems. A task that many homeowners may have to perform at some point is replacing bathroom pipes. This guide will take you step-by-step through the entire bathroom pipe replacement process, from planning to finishing.

Evaluating the state of your current pipes is crucial before beginning the replacement process. Keep an eye out for damage, leaks, and corrosion. In the event that any problems arise, a replacement is probably in order. Planning is essential in this situation; make a note of the kind and size of pipes you’ll need to buy to guarantee a seamless transition.

Getting the required equipment and supplies is the first thing to do after you’ve decided that replacing the pipes is necessary. This usually consists of fittings, copper or PVC pipes (according on your preference), plumber’s tape, pipe wrenches, pipe cutters, and any other supplies unique to your plumbing setup. Having everything ready before beginning will facilitate the procedure and avoid needless delays.

It is imperative that you turn off the bathroom’s water supply before starting to remove the old pipes. Find the main water supply shut-off valve and turn it off for your house. After that, turn on the bathroom faucets to let any leftover water escape the pipes. In addition to preventing water damage, this step helps to make the removal process safer and easier to handle.

You can now begin removing the old pipes after turning off the water supply and emptying the pipes. Disconnect any fixtures (such as sinks, toilets, or bathtubs) that are connected to the pipes first. To loosen and remove any nuts or connectors holding the pipes in place, use your wrench. Old pipes may be brittle or corroded, so proceed with caution when removing them to prevent breaking nearby fixtures or surfaces.

We will find out when you need to replace

There could be a number of reasons for this:

• physical depreciation expressed in the formation of leaks;
• clogging of old metal pipelines with corrosion products and lime precipitation on the walls, which can lead to a complete overlap of the lumen in them;
• The vibration of the pipeline system for pressure drops, which can lead to complete destruction of the water supply.

Which pipelines are installed in the bathroom is something we find out. Take note of the water’s temperature in them to accomplish this. She could be:

• hot – for household needs;
• cold – in general water supply for various household needs and mixing with hot water to the desired temperature;
• hot heating systems;
• Since on average one person can be spent more cubeter of water only for household needs, the task of removing the used liquid according to the sewage gravity system is relevant (in private houses in the summer season, this amount increases to 3 cubic meters).

Not too long ago, pipelines in the bathroom with diameters of at least a quarter of an inch were installed using steel water and gas pipes manufactured in compliance with GOST 3262-80.

The ideal size for bathroom items is typically one that is between an inch and a quarter. It’s important that you thoroughly familiarize yourself with each step of the procedure before attempting to change the bathroom pipes on your own. We’ll talk about them below.

Dismantling outdated communications

The following is the order in which dismantling happens:

1. Initially, you need to block the water on the risers of hot and cold water supply.
2. Before you replace yourself, it is necessary to dismantle old networks. To do this, you need to disconnect the input pipe from the riser, and make sure that the entrance shut -off crane holds water well, if necessary, a plug is installed on this place. Even with a small leak of the bay of neighbors from below, inevitable, and this should be avoided.
3. Dismantled materials must be cut into sections. This is done so that it is convenient to take them out of an apartment or house.
4. Remove the water supply fasteners on the walls of the room previously removed the tile (if any) from the walls. It should be borne in mind that it is not recommended to use them repeatedly, since modern methods of installation and construction of fixers are very different from the previously used. It is necessary to remove not only clamps or brackets, but also dowels with which they were attached. The holes in the walls must be thoroughly covered with cement – a sand solution or its analogue.
5. Dismantling of the drain system is carried out by disassembly on the connections. The fasteners are first removed from them. Concrete stands that determine the slope of the plumbing system are not subject to replacement, they must be left in place. They can be used when installing a new sewage system to maintain a normative slope.

The age of the outdated drain system is the reason for their replacement. In the past, cast-iron products were utilized; however, their rough inner surface made them more prone to clogging and necessitated frequent purification.

As a result, it appears that replacing the bathroom’s drain pipe is required. The drain system riser is typically found in the toilet room; it is only found in the bathroom in combined bathrooms. However, neither the renter nor the property owner bears responsibility for this item; instead, the management company should be thinking about replacing it.

At the request of the housing owner, a community organization should replace the pipe riser in the bathroom.

What pipes to choose in the bathroom replacement room

When comparing modern materials to those utilized in the past, there are numerous advantages (cast iron, black metal, etc.D.). These days, it is common to find so-called plastic materials.

View the [SOCIALLOCKER] video.

These consist of metal, plastic, polypropylene, and stitched polyethylene, among others. Using them is highly recommended, and we will support our claim in the article.

You must choose the type of material to be replaced before replacing the bathroom’s pipes with plastic ones. There are many different brands of products available in the construction market; it is important to weigh the benefits and drawbacks of each product before choosing one.

Sewer system, what we pay attention to when choosing

There aren’t many options here; you can either use modern plastic products or classic cast iron.

Because of their superior inner surface and lack of tendency to clog, plastic ones function better. They are also lightweight, which makes delivery to the target easier.

Installing them is also not too tough. Rubber cuffs are used as a seal in the bell where connections are made. Every size comes complete with fittings to build drain networks of any complexity.

The following materials are used to make sewer pipes:

1. Polyethylene (PE) is a product of polymerization of ethylene gas at elevated temperatures and pressure. Depending on production technology, low pressure polyethylene (PND) and high pressure (PVD) are distinguished. It should be remembered that according to the strength and temperature characteristics, the first material is better.
2. Polyvinyl chloride (PVC).
3. Polypropylene (PP).

Sewer pipes can also be made from other polymer plastics, though this is much less common. They won’t be taken into consideration for the purposes of our review.

It is preferable to use polypropylene products that can stably withstand temperatures as high as +75 degrees Celsius and a brief increase to +95 degrees Celsius when replacing the bathroom drain pipe.

It seems unlikely that this system’s drain will get to these levels. Low-pressure polyethylene (PND) can be used for the outer drain network because their liquid has a lower temperature and they are significantly less expensive.

Less frequently than 50 millimeters, pipes measuring 30 to 40 millimeters are used to replace bathroom drain systems.

Prior to replacing the bathroom pipes with plastic ones, carefully consider all of their features and make the best decision.

We select the material for pressure pipelines of hot water

Given that plastic products cannot form a raid on internal walls, using them is a feasible option. Lime plaque just does not form on them because the material is chemically completely passive and resistant to the majority of household aggressive substances.

The most hazardous impact is caused by air oxygen, which enters the product’s pores and microcracks and enters the water from space.

Furthermore, it does not directly impact the material; rather, it accelerates the chemical deterioration of the pipeline’s metal components, which in the bathroom include the locking reinforcement and heated towel rail. They are thus frequently changed.

Oxygen protection was developed in order to overcome this disadvantage. This is accomplished by using 0.1 millimeter thick aluminum tape. It is wound on a screw line around a base, which is a blank in the shape of a pipe.

Laser installation is used to fuse the joint in the continuous mode of production. The metal shirt is then covered in yet another layer of plastic. This results in a three-layer product where the internal cavity is hermetically sealed off from oxygen infiltration.

A metal shirt varies like a thin shiny strip on its end cut. A red stripe is applied in addition to the exterior labeling, which is standard.

It is preferable to replace the bathroom pipes with oxygen-protected polypropylene when installing hot water pipe wiring.

Cold water pressure pipelines made of plastic

Products made of different materials can be used for these purposes. They are provided with a fiberglass reinforcing belt as a means of applying pressure.

Production technology is similar to installing an aluminum protective shirt, except that fiberglass threads are used in its place. Such a reinforcing layer is identified on the end cut by a dark concentric strip. A blue longitudinal strip designates the exterior.

When replacing bathroom taps to particular consoles (16), products with a diameter of 20–25 millimeters are used for internal stains.

Title: Replacing Pipes in the Bathroom: Step-by-Step Guide from Start to FinishEmbarking on the journey of replacing pipes in your bathroom can be a daunting task, but with the right approach, it can be a smooth and rewarding experience. The process can be broken down into several clear steps, starting with thorough planning and preparation. Firstly, assess the current state of your pipes and determine the scope of work needed. Next, gather all the necessary tools and materials for the job, ensuring you have everything you need before getting started. Once prepared, the removal of old pipes comes next, requiring careful attention to avoid damage to surrounding structures. Following this, the installation of new pipes begins, where precision and accuracy are paramount. Throughout the process, it"s crucial to double-check measurements and connections to ensure everything fits seamlessly. Finally, thorough testing of the new pipes is essential to guarantee they function correctly and prevent any potential leaks or issues down the line. By following these steps diligently and methodically, you can successfully replace the pipes in your bathroom, improving its functionality and ensuring its longevity.

Tools and materials that we will need during operation

Water supply networks can be installed using a specific set of instruments and equipment when bathroom plastic pipes are replaced. The properties of the materials used determine its composition.

The ability to work with PVC products calls for having scissors on hand for cutting tasks. Since cold welding and docking to the bell are the primary methods of connection, strict cutting perpendicularity is the primary prerequisite for completing this operation. In this instance, sealant is occasionally used in addition to the rubber cuff for sealing.

Should the decision be made to replace the bathroom with polypropylene products for the internal wiring, a special design soldering iron and a cutting tool will be required for the docking.

The compounds are important in laying because the physical properties of polypropylene products prevent it from being produced in rolls.

A range of fittings are used during installation to build water networks of any complexity. Transition metal – plastic components can be used in combination if needed.

Two distinct techniques are used when installing polyethylene pipes for docking during installation: fittings are used for products with a diameter of 20 to 63 millimeters, and end welding is used for other sizes.

Stitched polyethylene products are used to build hot and cold water networks in bathrooms. By using crimping fittings with specialized designs, the connection is made. They install using Submy devices.

Make sure the ends of the parts that need to be joined are clean before working with metal and plastic products. It is carried out by a unique instrument called the ender, which also needs to be accessible.

It goes without saying that additional general-purpose tools may be required during work:

1. Electric drill for drilling holes in the walls for installing brackets – holders.
2. Drill or boura on concrete of the required size.
3. Punch for punching holes in the walls through which replacing pipes will pass.
4. Cement – sand mixture will be needed to seal holes in the walls after laying, respectively trowel and other tools.
5. To cut the old water supply, when replacing the system, you will need an angular grinding machine – a grinder equipped with a metal cutting disk.

1. Fasteners for installing pipes, including brackets, dowels (plastic inserts into the holes), screws.
2. Screwdriver or set of screwdrivers.

The chosen installation scheme for the water supply determines how many basic materials are needed.

Step	Description
A	Assess the condition of existing pipes.
B	Prepare necessary tools and materials.
C	Turn off water supply to the bathroom.
D	Remove any fixtures connected to the pipes.
E	Drain any remaining water from the pipes.
F	Detach old pipes carefully to avoid damage.
G	Clean the areas where pipes were attached.
H	Measure and cut new pipes to fit.
I	Install new pipes securely.
J	Connect pipes to fixtures.
K	Test for leaks by turning on water supply.
L	Inspect connections and make adjustments if needed.
M	Seal any gaps with appropriate sealant.
N	Secure pipes in place with brackets or clips.
O	Reinstall fixtures.
P	Turn on water supply and check for proper functioning.
Q	Make any final adjustments if necessary.
R	Clean up work area.

The plumbing in your house can work much better and more efficiently if you upgrade the bathroom piping system. To guarantee a seamless and efficient completion of the process, adopt a methodical approach. Gathering the required supplies and equipment for the task can be done after carefully planning and evaluating your current setup.

When you have everything you require, it’s time to start the actual pipe replacement process. This entails removing the outdated pipes with caution so as not to harm the nearby fixtures or structures. Once the old pipes are removed, you can install the new pipes in the order that you have planned.

Paying close attention to details during installation is essential to guaranteeing that the new piping system performs as intended. This entails making sure that pipes are sufficiently supported and insulated to prevent damage and heat loss, as well as sealing joints and connections properly to prevent leaks. It will save you headaches later on if you take the time to do this correctly.

It’s crucial to thoroughly test the system after the new pipes are installed to make sure everything is operating as it should. This could entail testing the operation of any fixtures or appliances connected to the plumbing system, as well as running water through the pipes to look for leaks or obstructions. You can identify any problems early and take action to resolve them before they worsen by carrying out these tests.

In conclusion, replacing the pipes in your bathroom is a task that needs to be approached methodically, with careful planning and attention to detail. You can successfully upgrade your plumbing system and take advantage of increased efficiency and functionality in your house by following the above-mentioned steps. You should have years of good service out of your new pipes provided they are installed and maintained properly.

Video on the topic

Repair of the bathroom from A to Z. The whole process.

Budget repair of the bathroom and toilet in Khrushchev from A to Z. All stages, cost of work.

Bathroom repair all stages. Preparation of walls, communication, laying tiles, grouting, etc.D.

Bathroom. The whole process.

Pipe wiring in the bathroom. Water supply in the apartment

Installation of pipes in the bathroom

Secrets of the installation of polypropylene pipes. Master class for beginners