Maevsky valve for cast-iron radiators: how to choose, install and drain the air

The effectiveness of our heating systems is essential to maintaining a warm and comfortable home. For a long time, many homeowners have preferred cast-iron radiators because of their strength and capacity to hold heat. To operate at their peak, though, they need routine maintenance, just like any other heating system. The Maevsky valve is one crucial part that keeps cast-iron radiators operating at their best. This tiny but essential valve facilitates the free flow of hot water and effective home heating by releasing trapped air from the radiator.

It’s crucial to select the appropriate Maevsky valve for your cast-iron radiator in order to guarantee compatibility and efficient operation. Maevsky valves come in a variety of sizes and types, so it’s important to do your homework or speak with an expert to find the one that will work best for your radiator. The size and style of your radiator as well as the location of the valve installation are important considerations. While some valves are more adaptable and can be used with a variety of radiators, others are made especially for certain radiator models.

A Maevsky valve installation on your cast-iron radiator is a reasonably simple task that most homeowners with some basic do-it-yourself knowledge can complete. To make sure it’s done right, it’s best to hire a qualified professional if you don’t feel comfortable doing it yourself. Usually, the installation procedure entails removing the old air vent (if applicable), draining a small amount of water from the radiator, and replacing it with the new Maevsky valve. Before adding more water to the radiator after installation, it’s crucial to make sure the valve is operating correctly and look for any leaks.

Using the Maevsky valve to remove air from your cast-iron radiator is a crucial part of keeping it operating efficiently. As air builds up inside the radiator over time, it may become difficult for hot water to circulate correctly and cause uneven heating throughout your house. You just need to use the small screwdriver or key that usually comes with it to open the Maevsky valve and let the air out. A hissing sound will be heard, and then water will follow as the air leaves. You’re done when the water flows steadily and you close the valve! This simple and quick procedure can have a significant impact on how well your heating system operates.

Device and principle of operation

It should be mentioned that there are two varieties of Mayevsky valves: automatic and manual.

A needle-shaped locking screw with an outward-pointing hexagonal head and a screwdriver slot is installed inside the sleeve. On the side of the casing is where the outlet drain hole is situated. The opening can be conveniently positioned for water drainage by rotating the plastic rim around its axis.

The basic idea is to insert a screwdriver into the screw after removing the air lock. A half-turn or a full turn of the locking needle causes the inlet calibration opening to gradually open. The cast iron battery begins to let out the air that has built up in its upper section.

Automatic Maevsky valve

It is necessary to install an automatic Maevsky valve on old cast-iron batteries in areas of the heating system that are difficult to reach or where people are not always present. These could be utility rooms, interfloor passageways, etc.

1. Nipple is the device design. 2. Spool. 3. The springtime. 4. The spool shell. 5. Shut Up. 6. Stay afloat. 7. The case.

An empty metal cylinder serves as an automatic device. Its movable lever in the upper part holds a float that is fixed and connected to the valve. The automatic valve works on the basis of the float falling to the ground due to gravity as air builds up, opening the valve.

The outlet hole will close once more once the float is in its initial position due to the restored coolant volume, once all the air has been removed.

Peculiarities of operation

Tenants have to vent the air on the upper floors of old houses with cast-iron radiators at the start of the heating season. Apartment owners use screwdrivers to remove the slots from the manual Maevsky valve screws, making it harder for them to operate further.

Buying a specialized wrench that protects the screw head completely without scratching it is preferable in this situation. When purchasing valves, you can also select ones with rotating plastic handles.

At the radiator inlet, rusty scale can occasionally accumulate around the rim of an automatic or manual valve. This suggests that the rubber gasket needs to be replaced because it is damaged. If the cast iron radiator does not have a valve on it to disconnect from the heating system, it is challenging to do this during the heating season.

You can put off replacing the gasket until spring if there isn’t any coolant leakage. Rather than using a rubber gasket, a winding of linen wool is made if the thread in the radiator plug is damaged.

Plugs can be found in old cast-iron batteries by unscrewing their rusted inlet threaded holes, which have been left untouched for years or possibly decades. After cleaning, they are greased with mineral oil or another type of grease. The mounting lug is wrapped with linen wool and screwed in place.

It’s important to clean the old radiator to remove any rust buildup. Before the Maevsky valve is installed on the cast-iron radiator during the spring and summer, the radiator is taken out into the yard and removed. With the exception of one, all holes should be sealed with plugs.

The radiator’s open hole is facing up when it is positioned on a rib. Add 200 grams of caustic soda to 10 liters of water to make a solution. Give it a 24-hour soak. There is no more solution. Use hot water to rinse the radiator—ideally under pressure. The spotless radiator is put back in its position.

The Maevsky faucet’s outlet hole may clog with suspended particles in the hot water over time. A pin or sewing needle can be used to clean the window. Take caution not to interfere with the hole’s calibration. The valve is left open while cleaning is done.

How to choose

There are two thread sizes available for Mayevsky valves: ½ and ¾ inches. The valve must have a threaded hole made in it that is the same size as the air vent’s thread in order to be cut into the plug of a cast iron radiator. If you have the right tools, you can complete it on your own or in a workshop.

One can purchase a repair kit with plugs (lugs) ready for inserting Maevsky taps in the heating device market. All you have to do is choose the proper thread diameter.

Under a screwdriver and wrench are air ventilators with an adjustable screw. Using a faucet with a plastic handle that can be rotated is more practical. Housing and utility companies, as well as other businesses, purchase automatic air vents to install in public spaces, buildings, and structures. Rarely are they sliced into radiators made of cast iron.

For optimal air removal and effective heating, your cast-iron radiator must have the correct Maevsky valve. Maevsky valves come in a variety of styles, so it’s crucial to choose one that complements the size and style of your radiator. Seek for valves composed of robust materials, such as stainless steel or brass, as these will withstand wear and corrosion better over time.

Maevsky valve installation is a simple, do-it-yourself project that can be completed without expert assistance to save money and time. To ensure safety during installation, turn off your heating system first. Next, find the highest point (where air tends to collect) on your radiator. This is the Maevsky valve installation location. To ensure a proper seal, follow the manufacturer’s instructions and firmly attach the valve to the radiator using the appropriate tools.

Using a Maevsky valve to drain the air from your cast-iron radiator is an easy chore that needs to be done on a regular basis to ensure maximum heating efficiency. To start, set a container underneath the valve to collect any water that leaks out. Using the included key or screwdriver, slowly open the valve until you hear air escaping. Close the valve to stop any water leaks once the water is flowing steadily. To keep your radiator operating effectively, don’t forget to drain any trapped air and check the valve on a regular basis.

To sum up, a Maevsky valve is a useful addition that will help to ensure effective air removal and heating in any cast-iron radiator system. You can have a warm and cozy house free from heating problems by selecting the appropriate valve, installing it properly, and routinely draining the air. By following these easy steps, you can prolong the life of your radiator and maintain its performance, which will ultimately save you money.

When it comes to heating our homes, ensuring our radiators work efficiently is key. One essential component often overlooked is the Maevsky valve for cast-iron radiators. Choosing the right Maevsky valve can make a big difference in how effectively your radiator heats up your space. Installing it might seem daunting, but with the right steps, it"s quite straightforward. The valve helps in releasing trapped air, ensuring your radiator functions at its best. Regularly draining this air prolongs the lifespan of your heating system and keeps your home warm and cozy. So, understanding how to select, install, and drain the Maevsky valve can go a long way in optimizing your home"s heating and insulation.

Video on the topic

Removing air from radiators with the help of Maevsky valve

Drain the air in the radiators – Maevsky tap 12.11.19

Installation of a CROWN on a cast iron heating radiator. HEATING REPAIR.

How to remove air from radiators in centralized heating systems. 5-storey building. Maevsky tap.

How to drain air from radiators

How to easily deflate an old battery

Maevsky tap. Device.Installation. How to bleed a radiator.