Installation of water filters: connecting the filter for water purification, installation of a water filter, how to install, connect to the water supply

Every household needs to have access to safe and clean water. But occasionally, contaminants in tap water can degrade its flavor and quality. Water filters can help in this situation. By adding a water filter, you can help clean up your water and make it safe to use for cooking, drinking, and other domestic tasks.

A point-of-use filter is a popular kind of water filter that is usually mounted to the faucet or placed under the sink. To eliminate impurities and enhance water quality, these filters function by putting water through a variety of filtration media, such as ceramic or activated carbon. By following a few basic steps, installing a water filter is a relatively easy process.

Selecting the ideal kind of water filter for your requirements is crucial before installing one. Take into account elements like the amount of filtration needed, the size of your home, and the installation space. After deciding on an appropriate water filter, you can start the installation procedure.

Finding your home’s main water supply line is the first step in installing a water filter. This is usually located next to the water meter or the point where your home’s main water pipe enters. To avoid spills or leaks during installation, you must turn off your home’s water supply as soon as you’ve located the main water supply line.

The location of the water filter installation must then be decided. This will vary based on the kind of filter you selected and how your plumbing system is set up. While faucet-mounted filters are fixed directly to the faucet, under-sink filters are usually installed beneath the kitchen sink. For information on the precise installation requirements of your water filter, refer to the manufacturer’s instructions.

Once the installation location has been established, you can proceed with attaching the filter to the water supply. The filter unit may need to be inserted by cutting into the existing plumbing pipes, or it may just need to be connected to the faucet using the supplied connectors. Make sure you use the right tools and materials for the job and closely adhere to the manufacturer’s instructions.

You can turn the water back on and inspect for leaks or other problems after the filter is firmly attached to the water supply. For a few minutes, let the water pass through the filter to remove any loose particles or air bubbles. Your water filter should be ready to use once the water runs clear, giving you and your family access to safe and clean drinking water.

Installation of water filters: connecting the filter for water purification Connecting the filter involves finding a suitable location near the main water supply line, shutting off the water, cutting the pipe, installing fittings, and connecting the filter in line with the flow direction.
Installation of a water filter To install a water filter, you need to choose the right type for your needs, locate a suitable installation spot, shut off the water supply, prepare the pipes, mount the filter securely, and connect it to the plumbing.
How to install Installing a water filter requires shutting off the water, choosing a location for the filter, mounting it securely, connecting it to the water supply, checking for leaks, and ensuring proper filtration before turning the water back on.
Connect to the water supply To connect a water filter to the supply, first, shut off the water, then locate a suitable spot in the plumbing, install the necessary fittings, connect the filter securely, and test for leaks before turning the water back on.
Contents
  1. Criterias of choice
  2. Where to find a specialist?
  3. Installation of a crane for purified water
  4. Installation of a cartridge type filter
  5. How to correctly mount cleaners in the house and apartment?
  6. How to connect a system under a sink with your own hands?
  7. Installation and connection of the main system
  8. How to install a gross cleaning system?
  9. Installation of the softener
  10. Kinds
  11. Reverse osmosis system
  12. Requirements and rules for installing a water filter
  13. Installation process of cartridge filters
  14. Preparation for operation
  15. Necessary tools and components
  16. Why do you need a coarse cleaning filter in front of the counter
  17. What installation to filter water to choose?
  18. Combined boot for drinking water
  19. Instructions for geyser prestige
  20. The principle of water purification
  21. Used filter materials*
  22. Requirements for the source water
  23. PRECAUTIONARY MEASURES
  24. SPECIFICATIONS
  25. The electrical circuit of the reverse osmosis system for pump models
  26. Connection scheme and a set of geyser-player supply
  27. Connection scheme and a set of geyser-ptstizh-m
  28. Connection scheme and a set of geyser-pstiz-p
  29. Connection scheme and a set of geyser-play-pm
  30. System installation
  31. The sequence of installation of pre -cleaning cartridges in water filters
  32. Step -by -step instructions on how to install a filter for cleaning water for a sink
  33. How to choose and operate a filter for a high -pressure minimum
  34. Complex assembly of cleaners – installation scheme
  35. Connection of the water filter to the water supply: installation procedure
  36. Video on the topic
  37. ✅ How to install a trunk filter # #repair #plumbing #live hacks
  38. Proper installation of a water filter.
  39. Installation of a drinking filter on the kitchen

Criterias of choice

You must adhere to the following advice when making your decision.:

  • Take into account the level of water pollution. How effective the cleansing system will work depends on the specificity of existing pollution. Therefore, it is recommended to analyze the liquid.
  • Pay attention to additional parameters. For example, water temperature. Most devices are designed to filter cold water. Therefore, if you need to clean hot water, you will have to buy devices with a high temperature limit.
  • Take into account the performance and resources of the filter module. The filter performance is determined by its ability to pass and conduct a certain amount of water per minute. This indicator is considered the minimum in the systems of the reverse osmosis, since it takes a lot of time to pass the fluid through the membrane. Therefore, you should decide how much purified water will be needed.
  • Accessibility of consumables. Filter modules often exhaust their resources quickly. Therefore, they will have to spend money on them.

Products from reputable manufacturers should be given preference as they are likely to meet quality standards and last for a long time.

Where to find a specialist?

Installing the filter can be done by them alone or with the help of an expert. There are a ton of offers for cleaning system installation on the services market today.

On the Internet or through recommendations from friends, masters can be found. Prior to selecting a specialist through an online resource, you should read client testimonials.

The kind of filter device will determine how much it costs to install the equipment. The following table displays the average price:

Type of filter The average cost of installation work, rub.
Castle filter for a sink with a drinking crane 2000
Magistral filter from 1000 to 2000
Reverse osmosis 2000-2500
Filter-gryazevik From 250
Complex cleaning installation from 10,000

Installation of a crane for purified water

A separate crane is installed for drinking water, or one is combined with the home’s hot and cold water supply. In the first example, the crane is part of the filter components. If not, you should buy a replacement along with the appropriate connector and adapter. The crane is placed away from the mixer, on a countertop or sink.

How to install a crane:

  • A 12 mm hole is drilled under the crane. For this, the corresponding drill is selected. First, it is recommended to use a drill by 5-6 mm, and then more.
  • The crane is installed in the finished hole through the seal on top and fixed with a nut, twisted from the bottom onto the half -pipe. Do not forget to check if all sealing gaskets are in place.

Installation of a cartridge type filter

Water can be cleaned of large mechanical impurities by using a coarse cleaning filter, but many inclusions of different kinds still remain in the water after that. Specifically, we are discussing different dissolved substances and small mechanical suspensions. Cartridge filtering devices are used to further purify the water. Comparable devices consist of a glass that the filter cartridge is placed into and a head portion that is fixed on a tap pipe.

Filter filler comes in a variety of forms, all of which purify water by removing impurities from specific sources. Coal, adsorbing, ion-exchange fillers, or the ability to carry out more delicate mechanical impurity purification are some examples (further information can be found in "Film filter – types, purpose, rules of choice").

There is a single filter installation scheme for purifying water that is independent of filler type in all cases. In particular, it is assumed that the following will happen:

  • Before installing a water filter, it is necessary to determine its location. It is important to take into account that the device should not interfere or undergo mechanical influences.
  • Next, choose the correct height of the location, here take into account the need for regular replacement of the cartridge. Therefore, in order to freely remove the glass, you need to withstand the distance from the filter to the lower surface of at least 10 cm. Knowing how to change the water filter, this can be done yourself.
  • Having chosen the optimal location option, they start installing a water filter. First, the water is overlapped in the system and open the nearest crane. Such actions will bring all the water that filled the pipes.
  • Then you need to cut a pipe section for installing a filter device.
  • Immediately in front of the location of the filter, a crane is welded, with which the supply of water to the filter will be limited.
  • To join the head part of the device, the couplings are used, upon the end of the installation, the joints are thoroughly checked. For more sealing compounds, you can use additional sealing materials.
  • The selected type of cartridge is freed from the packaging and inserted into a glass, which is further fixed on the head of the device.
  • After installing the water filter, the system and the new device are tested. For this purpose, a shut -off crane is opened at the entrance of the water pipe into the house and water intake crane. The water supply will identify defects at the installation site of the cartridge filter.

How to correctly mount cleaners in the house and apartment?

It is essential to install and link a water-cleaning device to a cold water supply system in order to organize the purification process. The hydrofilter’s type and overall dimensions are taken into consideration when choosing the installation location.

How to connect a system under a sink with your own hands?

The area beneath the sink is the most practical location for a reverse osmosis device and a running filter.

A few prerequisites must be met for the system to be installed in the underwear section:

  1. The presence of sufficient free space to install a cleaning device. The compression or squeezing of the component parts of the filter is not allowed.
  2. Free access for equipment maintenance. The location of the flask should provide unhindered replacement of cartridges.
  3. Free access for revision and repair of plumbing equipment – valves, siphon, etc.P.

The following collection of tools will be required for installation work:

  • drill;
  • drills with a diameter of 12 and 3 mm;
  • divorce key;
  • pipe key of 14 mm;
  • The cross -shaped screwdriver.

The supply kit comes with a connection node, supply tubes, and a special tap for cleaned water in addition to the running filter itself.

The locations of a crane and water-cleaning device are planned before installation work begins.

Additionally, a prototic type system is connected in the following order:

  1. Using a drill and drill in the sink, drill a hole for installing a crane. On the shank of the crane, put on a decorative washer and sealing gasket. Insert the tap into the prepared hole.Fix the tap to the lower surface of the sink by means of sealing gaskets, a stop washer and nut. Tighten the nut with a tubular key.
  2. On a filler pipe equipped with a brass insert, put on a pitch nut. Wrap the nut on the shank of the crane and tighten with a tubular key.
  3. Overlap the cold water supply. Drain the remaining water from the system, opening the cold water supply crane on the kitchen mixer.
  4. Understand the flexible hose connecting the mixer and supply the pipeline.
  5. Wind up the unit jail of the connection unit on the input pipe of the cold water pipeline, having previously convinced the availability of the gasket. To tighten up to the dial.
  6. Screw the united nut of the flexible hose to the threaded part of the connection unit, after making sure the gasket is available. Tighten the nut with a dilutant key.
  7. On the connection node, block the supply tap. Open the valve on the supply pipeline of cold water. Check the tightening connection unit.
  8. Assume the supply tube to the output fitting of the connection unit. Remove the stop clip from under the zangi. Introduce the pipe moistened with water to a depth of 15 mm. After that, fix the zanga with a stop clip.
  9. Collect the filter. On the wall of the cabinet under the sink, drill holes at the previously intended points, tighten the screws. Hang a water cleaning device on screws.
  10. Connect the pipe from the connection unit, connect. Connect the pipe going to the water tap for cleaned water to the output.
  11. Open the water supply crane, wait for air removal from the system. Close the tap. Check the nodes for tightness.

Speaking of which, It’s essential to flush the filter once installation is finished. Open the drinking water crane and take ten minutes off to accomplish this. After that, wait ten more minutes while tightening the tap. After turning on the water supply, wait fifty minutes.

Installing a reverse osmosis water cleaner works on a similar principle to installing a flow filter.

The requirement to affix extra elements makes a difference:

  • drainage clamp for the sewer;
  • membrane element;
  • cumulative tank.
    SECRIPTION OF NOTHER WORKS:
  1. Collect filters of the lower row of prevention.
  2. Installation of a membrane. Disconnect the flexible eyeliner at the entrance to the hull of the membrane. Unscrew the lid. Insert a membrane element and tighten the lid. Connect the phone to the hull of the membrane.
  3. Connecting to the water supply system. Block the water supply, lose air from the system, by opening the crane to the faucets. Disconnect the flexible hose. Mount the adapter tee and supplying valve. Connect the flexible hose of the mixer to the opposite end of the coupling.
  4. Installation of drinking crane.
  5. Connecting a storage tank. On the thread located on the lid of the accumulator tank, wind the fum tone and wind the ball valve. Connect one end of a flexible tube to the valve, the second-to the tee at the entrance to the post-filter.
  6. Installation of a drainage clamp. Unpack the drainage clamp, separate the front and back parts. Put on the elements of the clamp on the sewer pipe under the sink, fix it with two fasteners.In the center of the front of the drainage clamp, drill a hole with a diameter of 6 mm. Put on a flexible pipe to put a crimp nut, connect with a clamp. The free end of the pipe is connected to the limiter of the current.
  7. Washing the system.
    When performing work, use the FUM tone for the tightness of threaded joints.

Installation and connection of the main system

The purpose of the trunk filters is to purify the water that comes from the tap highway. The primary water purifier is constructed like a hermetic flask, with a mesh filter material or cartridge inside.

Guidelines for attaching the primary device:

  1. Block the introductory valve on the water supply system.
  2. Reset pressure on the network by opening a crane on any plumbing device.
  3. Indicate the location of the filter. Make holes in the wall, insert plastic flasks under the dowel.
  4. At the location of the water cleaning device, perform a visible rupture of the main pipeline. Rein the water cleaner into the highway through connecting couplings. For the tightness of threaded joints, use a fum tone. It is important to put the filtering device into the highway in accordance with the direction of the water flow. The filter is connected to the main pipeline by the side designated by the letters.
  5. Fix the filter on the wall using the fastener and dowels that are included in the device.
  6. To verify the quality of completed installation and flushing of the system, open the introductory valve and one of the taps for 5-10 minutes.

How to install a gross cleaning system?

The largest mechanical pollution particles are intended to be retained by the coarse cleaning filter.

A metal cylinder with a beveled branch for collecting dirt is the most basic kind of mud. The filter element is located inside the cylinder. The tube’s end sections have threads on them. On the case of the device, signs are applied. indicating the water’s flow direction.

After locking reinforcement, install a coarse cleaning water cleaner on an introductory pipeline prior to the metering device.

You will need the following supplies to install a mud connection:

  • two divorce or wraps;
  • plumbing linen or fum-knee.

There are multiple operations involved in the straightforward installation process:

  1. Block the introductory valve.
  2. Win sealing material on the filter thread.
  3. Wind the filter-gryazer on the Won Wentle Pipe. Spin.
  4. After the water cleaner, the water meter is mounted, I use the keys. One of the keys is held by a mud, with the help of the second, tighten the accounting unit. The filter-gryazevik is installed in such a way that the sump for the mud is below.
  5. Check the quality of work and the tightness of the system. To do this, open the water valve and include water.

Installation of the softener

The purpose of softeners is to lower the concentration of alkaline earthling metals. Elevated water hardness causes scale to form and has detrimental effects on household appliances and humans alike.

The tank-saturation and control unit, along with a flask containing a filter medium, make up the water softening device.

The installation is situated close to the sewer network’s passageway at the water supply input. One important consideration when deciding where to install a softener is whether or not free access is available for equipment and backfill reagent maintenance.

Speaking of which, It is advised to install a coarse cleaning filter in front of the softener.

  • turn off the water supply;
  • Connect the filter sailor to the water line by means of the mounting kit;
  • install the bypass;
  • connect the drainage line;
  • Connect the overflow pipe to the drainage system;
  • Rinse the filter;
  • check the tightness of the compounds;
  • connect the power supply and set up a microcontroller;
  • Fill a water tank with water and load salt.

Kinds

The drinking water filter cranes are composed of a variety of materials:

  • Brass is a reliable material that will withstand high workloads and maintain its original appearance for a long time.
  • Stainless steel is an excellent option that has an acceptable cost and high operational characteristics. The model in the style of minimalism will easily fit into any design.
  • Bronze at least looks solid and is characterized by high strength, but it is expensive and not every interior will look good. Such a water element should be chosen for rooms made in a similar style.
  • Cop of copper will last a long time even in conditions of increased operation.
  • Ceramics are just like plastic, even a thick one, is not the most durable option. Plastic is at least inexpensive, which cannot be said about ceramics. It is better to not choose such taps for the filter of water, if you do not want to soon be replaced.


Tap elements for filters are separated into two major groups based on constructive features:

  • Simple devices provide a separate supply of clean water. They are installed separately from the main crane through which ordinary, unpeeled water will be supplied. It is difficult to achieve a harmonious picture when there are two spouts near one sink.
  • Double models are suitable for providing the user with ordinary and tap water, the mixer can be installed in place. The only minus is the high cost, which begins with about 10 thousand. rubles. Such a high cost justifies itself.


The models that are being examined are frequently referred to as dual surgery devices. One or two pouring pipes may be included in the design. These models offer several benefits. First of all, there’s no need to drill a second hole that will eventually be impossible to fill. Second, the sink/shell appears more refined and organized.


Reverse osmosis system

Reverse osmosis systems give you the purest water possible at the output.

Although there are multiple features, the installation process follows a similar plan to that of installing a fine water filter. First, because of the way the filter is made and how it works, we are discussing how to set up the drain for the dirty water. The water molecules travel outside the otosmotic membrane as the water under pressure passes through its periphery, leaving all impurities behind. It is necessary to dispose of the concentrated solution that was created during cleaning in the sewer. Additionally, view "Which reverse osmosis system is better: benefits and drawbacks, installation"

A hole is made in it so that it can collide with the sewer system pipe. Clamp screws tighten tightly to guarantee a tight fit.

Another feature is that a storage tank must be installed in order to connect a water filter. This is necessary for the regular flow of re-based filtration. Even though the membrane’s cleaning process is slow, the storage tank gathers purified water to ensure a steady supply of water.

A hose from the filter is placed at the tank’s entrance, and a hose for the crane’s water supply is placed at the tank’s exit. Installing a locking crane on the tank is also necessary to cut off the water supply.

Following the installation of a water filter, the system must be launched by performing the following steps:

  • The tap on the tank is closed and water is served.
  • Then they open the tap of pure water and wait for a while.
  • The received water is drained.
  • Then the tap for clean water is blocked and open a shut -off tap on the tank. The received liquid should be poured to rinse the tank.

Requirements and rules for installing a water filter

The quality of water obtained from water supply networks is far from ideal. And what about the homes that get their water from a well or wells? Thus, in order to address the issue of quality improvement, many people install specialized under-sink filters. One must give due credit for installing a water filter. Additionally, while installation is not difficult in and of itself, the devices must be complete.

The problem is that there isn’t a single, universal filter that can purge water of all impurities. After all, both soluble and insoluble materials can be found in water. Furthermore, soluble can be postponed using fairly sophisticated devices that incorporate contemporary technological processes, if the latter can be resolved with ease by installing a mesh filter. As a result, it is essential to analyze the water to determine what contaminants and substances are present in it before installing a water filter under the sink.

All this will do is enable selection of the filter set that captures contaminants in the fluid. Every filter has a cost, after all. Additionally, the cost of the entire filter installation increases with the number of them installed under the sink. Therefore, two to six different types of filters will be installed, depending on the analysis of the home or apartment. Many residents take the easier route, selecting and paying close attention to one of the filtration zones.

For instance, you can use less expensive sorption in place of a deforming filter if there is a certain amount of iron found in the water and its concentration is not very high.

Installation process of cartridge filters

A plastic sealing glass with a shift cartridge inside is one component of thin filtration. The installation diagram of the water purification filter allows for the use of the incisade area (to supply fluid when clogging the cartridge), and couplings are used to connect the housing to the water pipe.

The water is purified of mechanical impurities after going through a metal mesh, but the liquid still contains a fine suspension of mechanical particles and solutions of foreign materials.

An algorithm for a DIY filtering device:

  1. Determine the installation site of the glass, the node should not prevent access to pipes and valves. To ensure the possibility of removing the external casing, a gap between the bottom of the case and the flooring is provided. It is recommended to withstand a distance of at least 100 mm, it is allowed to install a filter under the sink or place in a different place that provides protection of the plastic case from damage.
  2. Block the fluid supply into the room, and then drain the remaining water from the water supply through the mixer.
  3. To mark the pipe from which a section is cut out for installing a filter element and an additional tap necessary to turn off the water supply when replacing the cartridge.
  4. Connect a cartridge filter device to the pipeline using special couplings. The joints are compacted by rubber washers, a special sealant is allowed. The crane crashes according to a similar scheme. The installation of equipment requires the owner of the skills of working with plastic or steel water pipes, as well as the presence of a special tool and equipment.
  5. Extract the cartridge from the factory packaging, visually check the state of the node. Install the element inside the protective case or wind up on the lid connected to the pipe (depending on the design of the filter). Tightly tighten the threaded connection, the junction of the rubber sealing ring is provided at the junction.
  6. Put empty containers under the joints, and then open the taps (primary at the entrance to the room and reserve, located in front of the filter node). If the leakage of the fluid is noted, then the taps are overlapped, the joints are additionally sealed.

Preparation for operation

The primary work in preparation is:

  • Checking the tightness of all connections. Be sure to inspect all the seams, they should be created using a sealing tape.
  • Elimination of all pollution.

Washing involves removing minute particles from the components and manufacturing process of the material. In addition to potentially harming the body, leaving them in place will clog the outskirts.

The membrane tissue must be removed, and the fluid supply valve into the accumulative tank must be blocked. Next, open the faucet and remove fifteen liters of water. It will operate without a bay in a hydraulic tank, or in direct flow. Upon inserting the membrane, the hydraulic accumulator opens. You must now perform the flushing process once more. You are only allowed to use a water resource for drinking after the next fifteen liters. One cycle is sufficient if there is no tank.

Necessary tools and components

It suffices to have rudimentary plumbing knowledge in order to connect a water filtration system for the sink to the common water supply system.

Any filter’s set comprises elements like these:

  • cartridges, each of which is placed in its plastic flask;
  • connecting tubes (hoses) in the amount of 2 pieces – on the input and output;
  • fittings, a key for unscrewing and replacing cartridges;
  • brackets for fixation;
  • gaskets;
  • tap for filtered water;
  • tee (passing tap);
  • Installation manual (instruction).


A storage tank is a feature of some filter water system models. Even in situations where the pressure inside the pipes is low or weak, it helps ensure that water is distributed uniformly through the outlet valve.

For work, the following equipment will be required:

  • cutting for pipes;
  • Packla and Fum-Lent;
  • drill with different diameters;
  • Divorce key and knife.

Why do you need a coarse cleaning filter in front of the counter

Their service life will be prolonged by the installation of special coarse cleaning filters in front of the counter. Water must pass through several stages of cleaning before it can be connected to the city network. However, during this process, it passes through miles of rusted pipes, lime plaque, and other debris.

Groyazeviki compact mesh filters are used in local systems. They typically have a coupling threaded connection with a diameter of ½ to 2 inches, and are composed of brass. Although there are inexpensive alternatives, even spending a small amount of money on them is not advised because a product made of a questionable alloy may burst during installation.

When it comes to home renovation, having clean water is crucial for comfort and health. Water filters are an easy way to protect your water supply from pollutants and impurities. Simply install them. A water filter can be connected in a few easy steps, starting with selecting the best filter for your requirements and correctly installing it on your water supply system. This guide aims to provide you with a clear and simple process so that you can maintain clean and safe water for daily use.

What installation to filter water to choose?

There are various choices for combining different cleaning techniques. The decision is based on the water’s chemical makeup, level of pollution, and intended use.

The water supply for a home may occasionally split into two streams at the end.

One goes to the bathroom and laundry room for household necessities, while the other goes through the last cleaning and enters a different drinking crane.

Compact stationary installations under the sink in the kitchen are appropriate for a private home or apartment with moderate water consumption. It is most convenient to install the drinking crane next to the standard here and connect the apartment’s water filter to the water supply.

Combined boot for drinking water

Sometimes it is not convenient to have a separate crane for drinking water. In certain situations, a combined device that can serve both filtered and unpeeled water may be the best option. It is not like a traditional mixer because it has a separate valve on the case and an extra channel with a hole for drinking water on the common nose. The device allows water to be served from a single pill of varying quality, which is far more convenient than two separate cranes in a shared sink.

Important details: gas board hose dimensions and types, maximum length, and service life

See also: The best drainage pump to select for dirty water: types, distinctions, and features of options

Various materials are used to make devices:

  • stainless steel;
  • bronze or brass;
  • Plastic or ceramics.

But you will have to pay a high price for convenience—such a mixer is not cheap. You can opt for a less expensive plastic product, but while it has some benefits like not corroding or snatching, it does not last very long.

The best mixers are bronze with ceramics inside.

Coatings that mimic marble, copper, platinum, gold, or silver can be applied to products. Lever or valve handle mechanisms are also possible.

Instructions for geyser prestige

The principle of water purification

The Geyser-Pestizh series of filters use an interchangeable filter element multi-printed circuit for air conditioning and water cleaning.

Used filter materials*

  1. Mechanical cartridges from polypropylene fibers (EFM or PP series) are cleaned of water from dirt, suspended particles and insoluble impurities. Resource up to 6000 l.
  2. The CVS cartridge is made of high-quality pressed coconut coal according to Karbon-Block technology. Has a greater sorption ability than granular carbon, providing better water purification. Eliminates the smell, improves the taste and color of the water. Removes most organic compounds. Resource – up to 7000 liters.
  3. When cleaning water by reverse osmosis, special membranes are used. Through the holes of the membrane (10-10m.) only water molecules pass, so the cleaning efficiency can reach 99.9%. Membrane resource – up to 3500 liters.
  4. To completely eliminate the smell of water, a postfilter from pressed activated coconut coal is used. Resource – up to 6000 liters.
  5. The mineralizer was created on the basis of exclusively natural components. Saturates water with useful mineral salts and trace elements. Resource – up to 6000 liters.

Requirements for the source water

Take note! The geyser filter’s performance is not impressive if the water pressure at the input is less than 2 atm for pomp systems and 3 atm for pumpless systems.

Water pressure at the entrance to the system with pomp, atm 2-8
Water pressure at the entrance to the system without a pump, atm 3-8
pH 3-11
Water temperature, ° C +4 …+40
Mineralization, mg/l no more than 1500
The concentration of chlorides is total, mg/l no more than 1200
Turbidity, mg/l no more than 1
Stiffness, m-ekv/l no more than 7
Iron (Fe2+), mg/l no more than 0.3
Iron (Fe3+), mg/l no more than 0.3
Manganese (mn), mg/l no more than 0.1
Permanganate oxidation, mg o2/l no more than 10
Total microbial number, COE/ml no more than 1000
Coli-index 1

Higher indicator values necessitate more initial cleaning.

The membrane’s service life could be shorter than a year if the source water’s qualities don’t match the requirements.

PRECAUTIONARY MEASURES

  • Protect the system from shock, falls and freezing water in it.
  • Rinse the system, as indicated, before the start of operation, after cleaning and replacing the interchangeable elements and with long-term (more than 2 weeks) breaks in use.
  • In the process of water filtration, all cartridges should be in their places, and the tubes should not bend steeply.
  • Although the system delays and suppresses bacteria and viruses that can be contained in the source water, it is recommended to use it only with water, which is safe in microbiological terms and meets the “source water requirements”.
  • Do not filter the water of unknown quality.
  • If the water is not a city water supply, it is necessary to analyze it.
  • Do not store the system and cartridges near aerosols and toxic substances.
  • Do not make changes to the design of the system.

SPECIFICATIONS

The volume of the storage tank (the volume of water in the storage tank is 40 … 70% of its volume, depending on the pressure in the supply water supply), l 12*
Excessive air pressure in the storage tank, atm 0.4-0.5
Productivity (depends on the pressure and temperature of the water), l/day up to 200
The temperature of the purified water, ° C +4 …+40
Dimensions (without a storage tank), mm 470x380x420

* Potential apparatuses having 7.6 and 3.8 liter storage tanks.

The electrical circuit of the reverse osmosis system for pump models

Connection scheme and a set of geyser-player supply

I: The mechanical filter housing

II, III-

IV is the reverse osmosis membrane’s hull.

V – Coal post filter corps

* Without updating these instructions, the manufacturer maintains the right to make small changes to the system’s completion and design.

** Configuration possibilities with 12, 7.6, and 3.8 liters of storage

Connection scheme and a set of geyser-ptstizh-m

I: The mechanical filter housing

II, III-

IV is the reverse osmosis membrane’s hull.

V – Coal post filter corps

* Without updating these instructions, the manufacturer maintains the right to make small changes to the system’s completion and design.

Connection scheme and a set of geyser-pstiz-p

I: The mechanical filter housing

II, III-

IV is the reverse osmosis membrane’s hull.

V – Coal post filter corps

* Without updating these instructions, the manufacturer maintains the right to make small changes to the system’s completion and design.

Connection scheme and a set of geyser-play-pm

I: The mechanical filter housing

II, III-

IV is the reverse osmosis membrane’s hull.

V – Coal post filter corps

Case of the mineralizer, VI

* Without updating these instructions, the manufacturer maintains the right to make small changes to the system’s completion and design.

System installation

We advise hiring experts to install the system or installing it precisely in accordance with the instructions.

Disassembling the factory connections is not advised as the system is delivered in a collected state and is high pressure tested.

The cold water line is where the system is connected.

The sequence of installation of pre -cleaning cartridges in water filters

Cartridges are installed from right to left in water filters and auro reverse osmosis systems, similar to most filters from other manufacturers. The water connection is made to the extreme right flask, which is thought to be the first, respectively. A mechanical cleaning cartridge is always inserted in the first flask (next to the water) to collect mechanical pollution. Typically, a bulk filling cartridge—which may contain granular charcoal or a variety of resins and sorbents—is placed in the middle flask. Typically, a mechanical cleaning cartridge or one containing pressed coal (STO) is put in the last flask rather than the first.

The installation process will be as follows if you install a standard set in the filter, which consists of one polypropylene and two coal cartridges:

The installation procedure will be as follows if you install a set with double mechanical cleaning in a filter, which has two polypropylene and one coal cartridge:

  1. polypropylene cartridge 20 mkm PP;
  2. Activated coal cartridge GAC or CTO;
  3. Polypropylene cartridge 5MKM PP.

The installation process will be as follows if you install a set in the filter that has a softening effect:

  1. polypropylene cartridge 5MKM PP;
  2. cartridge with ion exchange resin (softening);
  3. CTR cartridge of activated coal CT

Should you install a filter set that has a defining effect. The following will be the order of installation:

  1. polypropylene cartridge 5MKM PP;
  2. cartridge with a defending sorbent;
  3. CTO activated activated coal cartridge.

Step -by -step instructions on how to install a filter for cleaning water for a sink

One of the easiest ways to purify the water in the apartment is to use a filter pump. The water crane is directly connected to it. One filter update is not sufficient if you’re interested in a more thorough purification of your tap water. Investing in and installing a filter to purify sink water is preferable. This can be completed on your own, without the master’s assistance.

Step 1: We choose the installation location. Consider the next steps of the filter’s operation before installing a water purification system under the sink. For example, it’s crucial to leave enough space for free access when changing the filter element. Depending on where it is most convenient to use, the water treatment filter may be placed underneath the sink in a vertical or horizontal orientation. You can install it even in the kitchen cabinet because the tank’s placement has no bearing on the filter’s quality.

Step 2: We contribute to the water supply infrastructure. First, turn off the water supply for a short while. Wrap all threaded connections after that. The insert can then be mounted. Disconnecting the cold water supply line will be the next action to take. It’s underneath the sink. Next, carefully secure the installed insert. Take caution: the tubes need to stay in the right place without moving around unnecessarily.

Keep in mind that you must always have easy access to the filter when installing one to purify water using a reverse osmosis system.

Step 3. We install the drinking water crane. When buying a filter for water purification, pay attention to the package: it should contain clamps for pipes and fasteners. For the correct installation of the filter to clean the water for washing, an additional hole is necessary to draw a tap from which the purified water will flow. If such a hole is not provided, then it can easily be done using a drill and a drill with diamond spraying. Drill diameter no more than 13 mm. Then remove the entire surface enameled or porcelain layer up to the metal frame. Next, change the drill, take a diameter of 7 mm. We drill a hole in the metal. It is important to be as cautious and neat as possible. Then we change the drill again and now we increase the hole to 13 mm. Only after the work done can you go to the installation of the crane from the filter to clean water for the sink.

Step 4: Put the clamp in place. Position a clamp on a pipe, either vertical or horizontal, just above the hydraulic shutter. Subsequently, we require a 7 mm drill bit once more to create a hole in the drain pipe. We reattach the gauze covering the opening. Next, we install a clamp support so that the pipe’s holes line up with its own. We need a drill that is tightly fitted with two screws to speed up the process.

Step 5: A storage tank is installed. It is crucial to consider the internal pressure of a storage tank during installation, as it should be between 0.54 and 0.95 atmospheres. Wrap the tape thread for the proper installation. Next, fit a storage tank with a plastic tap. It is strictly forbidden to tweak threads in order to prevent system failure. Determine the location for him beforehand, prior to the accumulative tank being installed directly.

Step 6. We start the filter. After full installation of the filter under the sink, start the water supply. In order to avoid leakage, make sure that the valve on the storage tank is closed and the “OFF” position is turned on. Open the crane through which filtered water should be supplied. After 10-15 minutes, water will begin to flow. A competent installation of a filter to clean water for a sink should end with a complete flushing of the system. After that, open the valve of the storage tank, having previously closed the tap with cleaned water. This is necessary in order for water to get into the tank. Когда бак будет заполнен, откройте кран и дайте воде протечь. Remember: the water of the first filtration is not recommended for use.

When purchasing a water filtration system, be sure to look for instructions. It is required to install a filter on your own, without the help of a master, to clean the water for a sink.

How to choose and operate a filter for a high -pressure minimum

The following indicators show differences between the filters offered for minimals in stores:

  • Filtration opportunity. This indicator is measured in micron. The less it is, the better the water purification.
  • Permissible temperature of the supplied water. Usually not higher than 40-60s.
  • Operating pressure. Can be from 6 to 20 bar.
  • Performance. In filters for Kerher"s washing, this indicator is on average 55 l/min.
  • Configuration of connecting elements. Standard indicator for high -pressure car wash – ¾ inch.
  • Materials used to manufacture a device. The most common is plastic, but there may be a metal inserts.

How to select a filter for a minimum high-pressure home

Things to consider when making a decision:

1. Dismantling. Since it is simpler to shoot and rinse such a filter, stores primarily display the primary models.

2. The potential for repeated use. Models that are reusable will endure a long time.

3. The ability to pass. Select models with a minimum indicator size of 50 microns. This will cover the necessary cleaning for the first stage of household minimums.

4.Universality. Universal filters are compatible with minimers made by a variety of manufacturers, so you can keep the filter in place even if you decide to switch equipment at the last minute.

Complex assembly of cleaners – installation scheme

Cottage and country house owners are particularly fond of complex installations.

The fluid is simultaneously purified by the water-cleaning system from:

  1. mechanical impurities,
  2. gland,
  3. Salt manganese,
  4. soften water.

A complex network of filtering devices is installed as part of the water purification system. The complex generates clean water for drinking and domestic use and is installed on the water supply system’s input. Order of priority for connecting actions:

  • Mechanical cleaning filter.
  • Compressor.
  • Filter colon.
  • Filter-retardant.
  • Salt tank.
  • Softener.
  • Water flow sensor.
  • Coal filter of thin cleaning.
  • UV sterizer.

Connection of the water filter to the water supply: installation procedure

Independently checking the quality of drinking water is crucial right now. Since water is not always present at the appropriate level in public utilities, it is not worthwhile to hope for the supply. A responsible owner will always install a filter to clean the water used for cooking and drinking. This apparatus will guarantee the elimination of chemical substances and mechanical contaminants, enhancing flavor and preserving well-being. Instead of hiring experts, we advise you to learn how to install a water filter on your own.

Blockquote P, Version 2.0.0.0.0 ->

Blockquote 3.0.0.0.0, P ->

The type of pollution, amount of water used, and usage circumstances all influence the modification of the filter device.

Blockquote 4.0.0.0.0, P ->

Advice: Before making a purchase, find out if future replacement filter cartridges and the required spare part are available.

If water is needed, juggling is an option. It is also more portable, requires no installation, and can be taken on a trip to the cottage or the outdoors because the filter element can be placed in a jug with just one motion.

P, 6.0.0.0.0 Blockquote ->

It is essential for your family’s health and safety to have clean water in your home. A useful way to get rid of pollutants and impurities and have clean, safe drinking water straight from the tap is to install a water filter.

It’s not too difficult to connect a water filter to your home’s water supply if you have some basic plumbing knowledge and basic tools. The majority of water filters include thorough installation instructions, making them easy for homeowners to install themselves. To guarantee proper installation, it’s advisable to always seek professional assistance if you’re unsure or uneasy working on DIY projects.

Finding a good location close to your main water line where the filter can be readily accessed for maintenance is the first step in installing a water filter. This could be in a utility room or beneath your sink. To avoid leaks during installation, you must turn off your home’s water supply as soon as you’ve determined the location and remove any leftover water from the pipes.

The filter kit comes with the necessary fittings and tubing to connect the filter to your water supply line. This is the next step. To guarantee a safe and leak-free connection, it is imperative that you closely adhere to the manufacturer’s instructions. After making sure the filter is firmly attached, you can restart the water supply and look for any problems or leaks.

It’s crucial to completely flush the system after the filter is installed and linked to your water supply in order to get rid of any debris and air bubbles that may have accumulated during installation. By doing this, you can be sure that your water filter is producing clean, pure water for you. Your water filter system will remain effective for longer if you perform routine maintenance, such as changing the filter cartridges as advised by the manufacturer.

Video on the topic

✅ How to install a trunk filter # #repair #plumbing #live hacks

Proper installation of a water filter.

Installation of a drinking filter on the kitchen

What type of heating you would like to have in your home?
Share to friends
Sergey Ivanov

I like to help people create comfort and comfort in their homes. I share my experience and knowledge in articles so that you can make the right choice of a heating and insulation system for your home.

Rate author
vDomTeplo.com
Add a comment