Installation installation for the toilet – determining the height and width, instructions for installation

One of the most important jobs in bathroom renovation or construction is installing a toilet, which calls for meticulous planning and execution. In addition to guaranteeing comfort and functionality, proper toilet installation also averts potential plumbing problems. This article provides comprehensive, step-by-step installation instructions after guiding homeowners and do-it-yourselfers through the process of determining the appropriate height and width for a toilet installation.

The importance of the measurements involved must be understood before you start the installation process. To make sure the fixture fits comfortably in the available space and complies with local building codes, the toilet’s height and width are important measurements. Additionally, the proper dimensions support the ergonomic use of the toilet, meeting the requirements of every household member.

You can install a toilet with confidence if you follow the simple instructions and useful advice in this guide. If you are installing a new toilet or replacing an old one in your bathroom, these guidelines will help you achieve a successful setup with maximum functionality and visual appeal.

Here"s a simple HTML table with basic instructions for installing an installation system for a toilet, detailing how to determine the height and width, along with a step-by-step installation guide:htmlCopy code

What is the installation for the toilet

A unique design and installation will also be required if the owner wishes to install the well-liked suspended toilets or bidets. It carries out the subsequent tasks:

• supports the input of the sewage system;
• supports the entrance of pipes with water;
• Sometimes – holds the water tank.

By using suspended toilets, you can clear more space and avoid having moisture under your plumbing. An additional benefit is that you can replace the floor tile coating without having to disassemble the product.

The back wall will move forward by 20–25 cm, so it is advisable to consider this when placing plumbing appliances.

Polymer is typically used to make the tank. It won’t be accessible once the installation is completed, to. External trim, like ceramic tiles, completely overlaps the built-in system. The owner will only be reachable by possibility once the installation is finished.

For this reason, it’s crucial to start with high-quality plumbing equipment. Should there be a malfunction, the steps will need to be repeated: take out the tile, take apart the bull, and then put the system back together. The landlord will pay a lot more for this than they would if you had started with high-quality plumbing.

The width and height of the installation

It is essential to ascertain the toilet installation’s dimensions prior to beginning construction. The structure’s depth, t.To, is its most important feature. This affects how conveniently plumbing functions.

The depth changes according to the system’s variety:

• block (10-15 cm);
• frame (15-30 cm).

It’s best to leave at least 0 in front of the restroom.Block-type installations are therefore advised beneath the capital wall since there is 6 meters of available space. This will provide fifteen centimeters more of clear space than the standard toilet that is currently in place.

The bathroom will seem larger with this installation, but it will also be more spacious. One more benefit of the block system is that it is less expensive than the frame.

The built-in tank is flat, has a small thickness (about 0.9 m), and has improved overall characteristics as a result of the low installation thickness. Since the tank’s width is typically 0.5 m, the toilet installation’s total width is likewise 0.5–0.6 m.

Additional installation sizes beneath the toilet:

• Height – in a design of a block type 0.8-1 m, frame type-1-1.4 m;
• The sewer output pipe where the plumbing is connected should be about 22 cm from the floor;
• Fasteners for the studs on which the product is suspended should be located 32 cm from the floor, however, this value can be changed by regulating the legs;
• The distance between the fastening axes is 18 or 23 cm.

The toilet measures 30 cm from the floor when its width and height are equal. This usually works well for every apartment occupant.

The suspended toilet’s cup has fairly standard dimensions:

• Width (0.thirty.4 m);
• Height (0.thirty.4 m);
• The length depends on the specific model: “mini”-up to 54 cm, “standard”-55-60 cm, “maximum”-70 cm.

Types of installation systems

There are various kinds of installations; they vary in size and design, especially in terms of depth and height. It is advised to research the key characteristics of the various systems in order to select the best one. Three different installation types are available for suspended toilets:

Sometimes the installation is categorized according to its intended use. For example, there are models appropriate for specific plumbing types in addition to universal choices. Additionally, release the toilet’s angular installation separately. Although it is not frequently used, it is essential if there is at least some open space in a combined bathroom.

Blocks

These models have two design components: an integrated module and a direct toilet. The built-in module is situated behind the falsehood, and the toilet bowl is either mounted on the floor or suspended using specialized mounts. The drain tank may be hidden behind a plastic or drywall partition, suspended, or walled behind cement and bricks.

The following attributes define block installation:

• a flat drain tank, additionally strengthened, having a small thickness, but a large width and height;
• peculiar elements for fastening.

Block installation is less expensive and requires less depth than the frame system. On a capital wall, installation takes place. The only thing that separates a standard (non-suspended) plumbing model from an ordinary system is the drain tank’s hiding.

It is preferable if the installation was already in the wall because it is nearly entirely built into it. A tiny nook is furnished. In cases where free system access is necessary or when funds are limited, a comparable variety is selected.

The primary disadvantage is that a toilet installation can only be completed in the presence of a capital wall. It is preferable to focus on t.To, a different kind of system, if it is not present. A sitting person’s weight will cause a thin partition to collapse.

Frame

The robust steel frame that forms the system’s foundation is coated in an anti-corrosion solution. In certain instances, welding is used to connect the components in order to guarantee increased installation strength. The entire weight, including the water, the sitting person’s body, and the elements, is supported by the steel frame.

The primary benefit of installing this kind of toilet is that it can be placed anywhere in the bathroom where the water supply and sewage pipelines can be brought. The purposes of different frame systems vary. There are models with various plumbing devices installed, and there are options that are only appropriate for a toilet or bidet.

These kinds of installations are free-standing, not wall-fixed, and their sturdy, fortified legs support their entire weight. As a result, unlike the block, such a system can even be mounted on a drywall partition that isn’t too thick.

There are various kinds of mounts.

• fasteners to the wall at 4 points;
• fasteners to the floor, this design has additional supports;
• fasteners at 2 points to the floor and at 2 points to the wall.

Corner

When there is limited room for the toilet but it is possible to install plumbing in a corner, corner installation systems for toilets are installed. These models are typically mounted on the walls. They also let you customize the bathroom’s interior design and add more space, though installing them will cost a little more.

• a compact size that allows you to install models even in the smallest rooms;
• visual increase in space due to the fact that the center of the toilet is not cluttered with plumbing;
• You can place the toilet complete with a sink or bidet;
• There are 40 mm of space, within which you can adjust the height of the product;
• The toilet bowls, as a rule, have increased strength and wear resistance, even with high loads, cracks and other damage do not appear. Despite their external fragility, installation can withstand up to 500 kg of mass.

One of the corner variety’s features is that it can only be installed in combined bathrooms. This type of model will visually shrink a standard room with lots of open space when installed.

Installation installation of toilet – the necessary tools

You can start installing after deciding on an appropriate installation type and marking height, width, and other dimensions. The alignment of the floor is part of the preliminary work. The walls must be leveled before installing block installation. As previously stated, a capital wall, t.To., is required when installing a similar variety. The product’s entire weight will be too much for the typical partition to support.

The installation of the toilet must be placed in a suitable location that takes into account the installation’s depth and height. After that, water and sewage supplies must be brought in order to facilitate communication. It is imperative that the pipes be positioned in close proximity to the installation site.

• Drill with jackets on concrete;
• FUM-love;
• divorce key;
• hammer;
• screwdriver;
• Kern;
• corrugated pipe for sewage;
• building level;
• double drywall, but it must be increased water resistance.

Examine the installation process using the frame installation example.

We fasten the frame to the floor

1. Pre -installation of the frame, checking the construction level of height and horizontal placement.
2. Using a marker or pencil, it should be noted the points where the frame will be attached. Focus on the already finished holes in the installation.
3. Put on the steel frame, in the points marked at the previous stage, make holes for fastening. If installation is made in a concrete wall, in most cases, dowels are used for a hexagonal key.
4. The frame is installed in place, fixing parts are twisted into the created holes.

We set the height of the toilet installation

The installation typically has an adjustable height. The height from the flooring, or the level of the finishing floor, must be counted. In the event that the coating has not yet been applied, the approximate height of the coating is added to the toilet installation height.

The structure’s legs can be adjusted independently, giving the master the ability to slightly alter the height. After the right height has been determined, clamping bolts are used to secure it.

The bolts are weakened if the value needs to be adjusted. You should definitely use a level to check the product’s even horizontal location during the altitude changes stage.

We fasten to the wall

Adjustable bolts are typically included in the package and are used to implement wall fixation. The bolts are fastened to the upper frame angles at one end and to the wall at the other end with special dowels.

The installation must then be placed in a strictly vertical position, as you must ensure. The construction level needs to be fastened to the side racks. After that, the frame’s position in relation to the wall can be adjusted by turning the nut on the fastener element.

Although this leveling process is not very complicated, how it is carried out is crucial. It’s critical to precisely level the structure, making sure to check it from multiple angles.

It is necessary to press the mobile element onto the fasteners once the procedure’s master is satisfied that the toilet’s installation went smoothly. This will result in the screw being fixed and the product being firmly consolidated in one place.

Connecting sewage and water

Next, you must attach a sewer exit pipe to one that is marked on a frame. When connecting to the sewer pipeline, there may occasionally be a knee; if not, corrugated pipe intended for use with sewers must be used.

There’s an additional connection option. A plastic clamp ought to be situated on a steel frame for this. The pipe that connects to the sewer pipeline’s output must be connected to it. But in this instance, knowing the precise diameter of the pipes is required.

A suitable pipe connects the cold water supply to the drain tank. Almost any pipe can be used for a connection, and it’s crucial to guarantee the connection’s dependability. This is necessary to reduce the risk of fluid leaks and joint depressurization.

It is best to avoid using metalloplasty pipes with a financial press. Because of concealed communications, it is very challenging to regularly tighten such fittings for dependable functioning. It is advised to use copper, polypropylene, or polyethylene pipes that have a strong adhesion between their components.

A flexible hose connects the adapter and the tank’s entrance. Although it is advised to use a company product, any stainless steel plumbing hose will work in a pinch.

Finishing, installation of the button and toilet

Following the primary toilet installation, the remaining work should start to complete the finishing touches. The steel frame needs to be sewn with drywall after it is installed. Generally, two sheets are needed.

Marks for height and other dimensions are first applied to the wall, and the profile is then mounted on the points that are created. Following that, drywall sheets are attached to the profile.

Installing a button box before finishing will help keep construction waste and dirt out of the way. For two studs on which a toilet bowl is mounted, holes are cut in the drywall beneath the drain button, the sewage system’s output, and the water supply pipe. Tiles are installed following the installation of drywall sheets.

Once the finish is complete, you must cut the drain button box, which should have its borders roughly at the level of the tiles. Two fasteners will have the button installed on them. Next, the mechanism must be connected to the cable (for mechanical varieties) or hose (for pneumatic varieties). After that, the button needs to be positioned and fastened with bolts.

The unit’s installation for installation:

1. The gasket is mounted on stilettos is mounted.
2. The holes where the sewage system is connected and are sealed with a silicone agent intended for plumbing.
3. The design is installed on the studs, then rubber gaskets are installed on them, and fasteners are tightened.
4. The excess parts of the gasket are cut off with a sharp knife.

A toilet installation system installation is a crucial task that needs to be done carefully and precisely. Comfort and functionality both depend on getting the right height and width. Most users find that a toilet’s standard height of 15 to 17 inches from the floor to the seat works well for them. For those who are taller or have mobility concerns, comfort height toilets, which are roughly 17 to 19 inches high, might be a better option. Conversely, the width of a toilet is primarily determined by the available space and its model, with the majority requiring at least 30 inches of space for installation.

If you follow the installation instructions provided by the manufacturer and make enough preparations, the installation process itself should be simple. Making sure there is no leakage and that all connections are secure is crucial. To ensure that the toilet is perfectly horizontal and avoid future issues, tools such as a level are essential. It’s also important to pay attention to the seal that exists between the toilet and the floor; a poor seal can lead to leaks and bad odors. The water supply line must be fitted, which should be done carefully to prevent cross-threading and leaks, as part of most installations.

Lastly, when installing your toilet, it’s important to take long-term maintenance into account. Future repairs can be avoided by selecting high-quality materials and carefully following installation instructions to save time, money, and effort. The life of your installation can be prolonged by performing routine leak checks, monitoring the flushing mechanism, and making sure the seal is intact. Your toilet installation can offer dependability and comfort for many years to come with the correct strategy.

A simple but effective way to improve the look and feel of your bathroom is to install an in-wall toilet system. The secret to a good installation is figuring out the unit’s ideal height and width and making sure it satisfies plumbing and user comfort requirements. In addition to providing a step-by-step tutorial, this article explains how to measure, position, and fasten the toilet frame inside the wall cavity and connect it to the current plumbing system. Homeowners can ensure everyday use and a sleek, modern appearance by following these instructions.

Video on the topic

How to not install the installation of the toilet #035

What height to put to hang up to fix the suspended toilet for installation

Installation installation. Step-by-step instruction.

Always do so installation | Installation installation | Turnkey apartment renovation

Installation and installation of installation of the toilet with your own hands. The installation of installation with drywall.

The simplest installation of the installation of the toilet and the hidden button. I show all the stages!