How to tie the boiler with a hydrostrelka

To maintain a cozy and economical home atmosphere, efficient insulation and heating are essential. The correct integration of your boiler system with a hydrostrelka—a term used to refer to the piping system that joins your boiler to the rest of your heating infrastructure—is one of the most important components of this. It’s crucial to know how to tie your boiler and hydrostrelka properly if you want to maximize your home’s heating and energy efficiency.

Many heating systems are built around boilers, which supply the heat required to keep your house warm during the winter. But, the distribution of heat in your home can be inefficient without a well-thought-out and connected hydrostrelka, which could result in uneven heating and possibly higher energy costs. By connecting your boiler to a hydrostrelka, you can maximize comfort and reduce energy waste by ensuring that heat is distributed uniformly and effectively throughout your house.

There are a few key factors to take into account when connecting your boiler to a hydrostrelka. First and foremost, your hydrostrelka’s layout and style should be customized to the unique requirements and architectural features of your house. The ideal arrangement for your heating system depends on a number of factors, including the size of your living area, the number of rooms, and the thickness of the insulation.

Furthermore, the durability and functionality of your hydrostrelka depend greatly on the materials that were used in its construction. High-quality wear-and corrosion-resistant pipes and fittings guarantee years of trouble-free operation for your heating system, reducing the need for expensive repairs and replacements. An additional benefit of proper hydrostrelka insulation is the prevention of heat loss during distribution, which lowers heating costs and increases energy efficiency.

What is a hydrostrelka

A top-notch plumbing device called a hydrostrel (also known as a hydraulic or hydrodynamic separator or hydrodividing device) is installed in the boiler unit and house system piping scheme to distribute the flow of heating water over multiple heating circuits, including the external boiler and towel dryer.

The design features four connecting threaded or flanged sockets: the upper inlet, the lower outlet, and the remaining sockets, which are for the heating distribution circuits (CH). The design has a round or square cross-section.

The number and estimated hourly volume of the heat transfer fluid on the DO, as well as the boiler’s thermal capacity, will determine the hydrostrelka’s size. Standard hydrostrelka equipment includes:

• pressure gauge, thermometer;
• temperature sensor;
• thermoregulatory valve;
• shut-off and regulating fittings;
• a line for making up the network;
• drainage line.

Better modifications integrate the capabilities of a separator, air ejector, and temperature control of heating circuits with a flow distributor to remove suspended particles from the internal boiler drum.

Porous deaeration plates are positioned vertically at the top of the structure for this reason. At the bottom of the casing are the magnet catcher and sludge collector.

Purpose of the hydraulic boom

A part of the heat supply system that joins the various CHPs is called a hydrostreamer. By guaranteeing the lowest allowable pressure drop across the circuits, the device allows one or more circuits to be turned off without causing a pressure surge in the remaining circuits.

As a result, the performance of circulation pumps functioning in heat removal circuits is not affected by the boiler circuit pump’s operation, and vice versa, when hydrodistributors are used in heating systems.

In which case it is necessary

For home heating schemes with multiple independent heating circuits, the hydrostrelka works well. The manufacturer frequently mandates the mandatory installation of such a hydraulic separator in the schemes of piping heating sources, particularly when installing a boiler of European assembly.

Conditions for the hydrostrelay floor boiler installation that are required:

• for boiler units with heat output above 50 kW under warranty service;
• For branched schemes that require the creation of a reliable hydraulic regime and thermal balance;
• When connecting the hydronic shooter in parallel with the consumption circuits to minimize pressure and heat losses;
• to ensure the calculated temperature difference between supply and return;
• to prevent water hammer in the heating system;
• when it is necessary to equalize the heating water flows in the boiler and heating circuit;
• when it is necessary to balance the operation of several circulation pumps;
• when it is necessary to reduce the hydraulic resistance of the system.

Operating modes

The heating system can be piped using a hydraulic arrow in three different ways. First, when the boiler unit’s circulation electric pump fills the internal heating circuit to capacity with the full volume of the heating medium.

In actuality, this variant is quite uncommon. A steady flow rate of circulating water is ensured by modern automatic heating system regulation systems, which use thermoregulators to regulate the boiler’s heat output. Without these, such regulation is practically impossible.

When the water flow rate in one or more heating circuits is greater than the electric boiler pump’s capacity, the second type of hydrostrip operation is set up.

For instance, when the pumps are chosen improperly, this may occur. In this variation, the heated heat transfer medium is fed into the circuit along with return flow to guarantee the necessary water flow rate.

This option will significantly underestimate the water flow rate from the circuit and increase the temperature differential between the hot and cold water in front of the boiler, which is not acceptable for all unit modifications. As a result, it is not recommended for boiler operation.

The most effective piping mode is the third one, which is made to have a boiler pump capacity that is greater than what the DO requires.

Under this scenario, the boiler unit will function in minimum mode when the set temperature is reached, raise the water temperature, and redirect a portion of the supply coolant back to the unit through the recirculation line. The equipment will operate with high efficiency because the system will have a thermal balance.

Place of installation

The hydronic boom should be installed correctly according to these five general guidelines:

1. For proper operation of the distributor, it does not matter in which position the hydronic shooter will be installed. It is important only the direction of the end pipelines, on which the operation of the automatic air vent and the sludge removal system depends.
2. The distributor is installed after the valve of the boiler unit.The place of installation is determined by the heating scheme, it is located as close to the unit as possible.
3. In case of manifold scheme, the distributor is placed in front of the boiler unit.
4. If it is necessary to connect an additional electric pump, the distributor is placed between it and the outlet pipe for the heating circuit.
5. In order to correctly bind the solid fuel unit, the hydraulic arrow is included to the output and input of the coolant, then you can adjust the individual temperature for each circuit.

Connecting your boiler to a hydrostrelka is an essential step in keeping your house warm and energy-efficient. In order to accomplish this, you must connect your boiler to a hydronic heating system, which distributes heat throughout your house using water. By doing this, you can maximize the efficiency of your heating system, guaranteeing uniform heat distribution and cutting down on energy waste. You can reduce your energy costs and enjoy consistent warmth with proper installation. This post will walk you through the process of connecting your boiler to a hydrostrelka and offer helpful advice on how to improve the comfort and efficiency of the heating in your house.

Calculation of the hydro jet

In order to account for the maximum mode based on the boiler’s factory parameters, the hydraulic distributor is calculated using formula D:

The diameter of the hydrostrelka is calculated by factoring in the boiler unit’s design thermal capacity as well as the temperature differential between the return and direct.

The hydrostrelka’s branch pipe diameter for the incoming coolant is:

• D – D of the distributor body, mm;
• D – D of the inlet pipe, mm;
• P – design heat output of the floor standing boiler, kW;
• G – the largest flow rate of the heat carrier through the distributor, m3/hour;
• C – heat capacity of water, W/(kg*C);
• V – water velocity through the distributor, m/s;
• Q – calculated hourly water flow rate in the DO, m3/h.

Buy or make with your own hands

Between $200 and $300 US is the cost of a ready-made set of hydrostrels assembled in Europe with auxiliary equipment available through trade networks.

All of the benefits of using such a design in the heat supply system are available to the user who purchases it, including fuel savings, dependable thermal and hydraulic conditions throughout the network, and long-lasting primary boiler equipment.

In addition to resolving distribution problems, factory assembly safeguards the system against sludge deposits on internal heating surfaces, corrosion, and water hammer. Every design node is meticulously calculated, produced utilizing cutting-edge technology, and fine-tuned in a factory setting.

It is recommended that home masters with locksmith experience and all the necessary equipment perform hydrostrelka independently. Fortunately, there are quite detailed manufacturing methods and schemes available on the Internet these days. The apparatus speaks of intricate hydraulic products, and when creating them, the following should be considered:

1. The couplings should have symmetrical well-cut threads.
2. The thickness of the walls of the branch pipes is chosen the same.
3. The quality of the welds must be high.

How to choose a hydrostrelka

Only when a hydrostrip is properly chosen can it function as intended. The boiler’s heat output and the total hourly water flow rate for all boiler units are the two primary factors to consider when choosing a distributor. It can’t go over the water flow rate through the boiler circuit on an hourly basis.

Then, take note of the hydrostrelka’s design elements:

• cross-sectional shape – square or round
• number of spigots: 4, 6 or 8 inlets/outlets;
• water supply/drainage version;
• The method of installation of the spigots – on a common axis or alternating.

Experts recommend buying ready-made designs with pressure gauges, air vents, and sump for wall-mounted boilers and hydrostrelka in order to clear the water circuit of sludge.

Connecting your boiler to a hydrostrelka can be a wise choice if you want to increase the heating system’s efficiency in your house. During the cold months, this easy-to-use yet efficient technique keeps your home warm and comfortable in every corner by distributing heat throughout the entire space.

The ability of a hydrostrelka to control water flow is one of the main advantages when paired with a boiler. With a controlled flow of heated water through your home’s pipes, you can do away with the hot and cold spots that come with conventional heating systems and keep every room at a constant temperature.

Furthermore, connecting a hydrostrelka to your boiler can result in significant energy savings. You can minimize the amount of energy required to maintain a comfortable home, which will ultimately result in lower utility bills and a smaller carbon footprint, by optimizing the distribution of heat.

This setup’s adaptability is another benefit. It’s not too difficult to integrate a hydrostrelka into an existing boiler system or a newly installed boiler. Additionally, this setup should provide years of dependable performance with proper maintenance.

All things considered, connecting your boiler to a hydrostrelka is a useful and affordable way to raise your home’s heating efficiency. If you want to improve your comfort and save money on heating, this is a strategy worth looking into because of its advantages, which include easier installation, energy savings, and better temperature control.

Video on the topic

Simple but reliable boiler room for underfloor heating and radiators

How to tie a pellet boiler. Heating with hydrostrelka

Strapping of the boiler Protherm Klom 40 with hydrostrelka

Review of my object with the strapping of the boiler #Baxi slim and colector with a hydrostrelka company #ProxyTherm

Strapping of solid fuel and gas boiler through hydrostrelka (The simplest scheme)!In operation for 6 years!