How to make a stove for a garage on wood or working with your own hands

Want to stay warm in your garage during the chilly winter months without paying astronomical utility bills? You only need to construct your own wood stove. You can create a straightforward yet efficient heating solution to keep your workspace comfortable with a little imagination and some basic tools. We’ll walk you through the steps of building a wood stove for your garage in this guide, providing you with helpful hints and advice along the way.

Not only is building a wood stove for your garage a useful DIY project, but it’s also a satisfying way to stay warm. Building your own stove lets you tailor the design to your own requirements and tastes, regardless of your level of experience with home improvement. Seeing your creation come to life and fulfill its purpose can also be an enjoyable and rewarding experience.

The simplicity of a wood stove is one of its main benefits. In contrast to more intricate heating systems, a wood stove only needs a few basic parts that are easily found at hardware stores to assemble. This implies that you can complete the task without specialized tools or to be a skilled craftsman. You can quickly have a working stove up and running with a little time and effort.

A wood stove not only provides warmth but also a sense of independence. You’re taking charge of your heating requirements and lowering your reliance on outside energy sources by using the power of fire. This can be especially helpful in isolated locations or during emergencies when gas and/or electricity supplies may be scarce. You can feel secure knowing that you can stay warm even in the event of a power outage if you have a wood stove.

Which heater is better for garage

Using an electric heater to heat the garage is the simplest method. However, if you spend several hours a day there, it is impossible to avoid space accounts for electricity. It is preferable to store the bourgeois in the garage and use spent oil that has been drained from automobile units or to convert to wood-burning heating.

It is impossible to overlook the fact that the fuel is diesel fuel. However, using it to heat the garage room will be costly and difficult. Purchasing a dedicated diesel heater is unnecessary since DIY stoves that run on waste oil can also burn diesel fuel.

Using the heating for working and firewood as a starting point, we go over some potential DIY heater options below:

• a heater laid out of brick;
• firewood for a garage made of metal;
• stove in proven oil.

A brick stove is the trickiest option and cannot be constructed in a garage. Consider using at least tight iron wagons instead of brick buildings, where only a small heater can be placed. Indeed, designing a well-built brick stove is a challenging task that warrants its own discussion to outline the steps involved. As a result, metallic stoves for wood-burning garages are the most "running."

We make an economical bourgeois on wood

We invite the reader to familiarize themselves with the drawings of a more somber heater so as not to divert their attention from the plethora of well-known designs of basic wood bourgeois that are already available on the Internet. One of its unique features is that it has two smoke circuits, or moves, arranged inside the furnace body for optimal heat transfer. What, after all, is the primary disadvantage of the average bourgeoisie? That’s correct—low efficiency—because the majority of the heat released right away goes up the chimney.

Hot combustion products are retained in two directions via specific channels in a two-way metal stove that you build yourself before exiting through the chimney.

A large amount of heat is successfully transferred to the room because of this design, which makes wood heating more efficient and results in savings. However, comparing various furnaces in real life is required to evaluate this economy, which is not always feasible. However, you can be certain that you will receive more heat from a two-way stove for the garage shown in the diagram above.

The components listed below are required to create a heat source:

1. Sheet metal with a thickness of at least 4 mm, optimally – 5 mm. From it you cook the case, chimneys and doors.
2. For the vault of the fuel that experiences the greatest heat load, it is better to take a sheet with a thickness of 6 mm.
3. A pipe segment with a diameter of 100 mm per chimney pipe.
4. Reinforcement of a periodic profile with a diameter of 16-18 mm for the manufacture of a grate.
5. Corner No. 4, pipe 40 x 40 mm or other metal rolling for legs.
6. Ready -made handles for the doors.

Note: You must use low-carbon steel of the ST10 or ST20 brand in order to manually cook on a garage stove. When high temperatures are used to order highly carbon or alloy steel, the case may crack at the welds. The method for roughly identifying the steel brand that is specified in the manufacturing instructions for a bath stove.

We’ll walk you through the process of creating a homemade wood stove for your garage in this article. You can make an affordable heating solution that will keep your workspace warm during the cold months with a few simple tools and supplies. We’ll guide you through each step, from choosing the appropriate supplies to securely assembling the stove. This project can be completed by anyone, regardless of experience level, as long as they follow the directions carefully and have a little patience. By the time it’s all through, you’ll have a working wood stove that not only warms your garage but also gives your room a hint of craftsmanship.

On the useful improvements of the iron stove

There are various suggestions on how to improve the design mentioned above. First of all, because this area burns most frequently, the junction of the chimney pipe and upper plate does not prevent the junction from happening. The load that a chimney pipe places on the welded seam in addition to the high temperature is the cause. The chimney is usually not fastened separately by the garage owners, and the entire weight of the structure rests on the furnace’s upper panel.

The size of the fuel and, consequently, the length of combustion are not something the bourgeois on wood with two chimneys can brag about. However, Bubafonia-style homemade stoves with extended combustion are not the best choice for a garage. They require a good thrust chimney that is at least 4 meters high, which is not always the case.

By adjusting the two-way stove’s height arbitrarily or widening the case by 10 cm, the fuel capacity can be expanded. Because the garage owner can adjust the heater’s size based on the available space in the room, homemade heaters are a good option.

As seen in the picture below, adding multiple vertical ribs to the side walls will enhance the wood stove’s ability to transfer heat. By using the same corner or a strip that is 4 mm thick, the heater’s effectiveness and heat transfer area are both increased.

Suggestions. If a circular opening is carved beneath the burner in the upper panel, the potoloring can be utilized for warming or cooking meals.

Fuel heat gun

Every stove that burns coal or firewood has a major disadvantage. The heater only heats a portion of the space because it is located in the uninsulated garage corner. Work is uncomfortable and the opposite angle (usually at the very gate) stays cold. Many owners of garage structures lay the chimney crawl through the entire room, which solves only part of the problem.

A more comprehensive garage warranty can take pride in the design put forth by Vitaly Dashko, one of our specialists in the production of solid fuel boilers and stoves. The device consists of a vertically positioned, ancient gas cylinder with a separate chamber for forcing heated air into it. The drawings show the layout of this stove for the garage, complete with sizes:

The stove operates on the same principle as a heat gun. This is how the work algorithm appears:

1. A portion of firewood is loaded into the fuel and the ignition is made.
2. After warming up, a fan connected by corrugation is turned on to one of the heating chamber pipes.
3. Since the horizontal partition between the fuel and the camera perceives the highest thermal load, the air passing above it quickly heats up.
4. Hot air, leaving the second pipe, is supplied using a corrugated pipe to any point of garage. The angle where the unit itself is installed is warmed up from the side walls.

Steel ribs that expand the heat transfer area inside the chamber allow for intense heat transfer. The location of these ribs is clearly visible in the longitudinal and transverse section of a blazing stove shown in the drawing below.

The bourgeoisie has the benefit of not requiring a tall chimney, even though she still requires natural traction. An air supervisor can be any low-performing but suitable fan. A cooler from a computer power supply might be sufficient in a tiny space. Household duct fans, rated at 50 m3/h, are used in medium- and large-sized garages and installed on bathroom hoods. The "Snail" from the VAZ 2108 is one example of a supercharger that works well with an automobile stove.

How to make a garage bake from a cylinder

It takes a lot of preparatory work to build a wood stove in a garage. Initially, the top portion is severed at the welds at the cylinder. Previously, when using a grinder, you had to unscrew the valve and fill it with water to prevent the propane remnants from blowing up. Next, a 300 mm diameter circle needs to be cut out of sheet metal with a thickness of 4 mm, and an 80 mm wide strip needs to be cut out for the door frame. You can cut the strips into heat exchangers from the leftovers.

Advice: You can increase the volume of the air chamber in the stove by cutting off the upper part below the seam. This will increase the stove’s thermal power. But keep in mind that doing so shortens the furnace’s capacity and the amount of time it can burn in a single fireplace.

We continue our work in the following order:

1. The next step is to cut the reinforcement and manufacture a grate. There are no strict requirements here, do according to the model in the photo, trying to adjust the length of the rods to the size of the joint -protruding seam cylinder. After that, set the lattice in the lower part of the container.
2. In the cut cover, you need to perform 2 holes for the installation of threaded drives DN50. This size is optimal, but it is not necessary to withstand it, as well as the selection of drives with carvings. You can take segments of a pipe of suitable diameter, but do not make it less than 40 mm. Then weld the pipes in place, as shown in the photo:
3. Further, in the cylinder body, in accordance with the drawing, it is necessary to cut the openings under the loading door, the chimney hole was blown. It is necessary to insert door frames cooked from the prepared strip into the openings and boil them in a circle. Before installing the frame, you need to make the workpieces of the door themselves, brewing loops and purchased pens to them.
4. The next stage is the formation of an air chamber. The prepared circle with a diameter of 30 cm is laid instead of the cut off the cylinder cover and welded tightly. After that, heat exchange ribs are attached to it by welding. Their number and placement may be arbitrary, but do not overdo it, otherwise you will have to select a more powerful fan that can overcome the aerodynamic resistance of the camera.
5. The last step is to weld the lids with the pipes in place and installation of the door with locking devices. At the very end, a chimney pipe is installed. Instead of the pipe, the finished knee is also suitable under 90 °.

It should be noted that the same wood stove for a garage is constructed with a large diameter pipe (300 or 400 mm) and a 4 mm wall thickness. The work will only be marginally bigger; the bottom and lid will need to be made independently.

Water heating connection

The garage furnace’s previous design was quite capable of heating water or antifreeze instead of air, allowing the water to be heated all the way around the curve. Overall, cutting the DN25 nozzle into the camera cover and buying a low performance circulation pump (marking 25–40) are required in place of DN50 drives. The pump is required because the furnace’s water circuit has an insufficient volume and the coolant will boil quickly in the absence of forced circulation.

The rest is easy: the stove pipes are linked to DIY registers or heating radiators with a maximum heat transfer capacity of 3-3.5 kW. It is advised to connect using metal pipes, or in very rare circumstances, metal and plastic. An expansion tank of the closed type must be placed in front of the pump, which is mounted on the reverse pipeline in front of the stove. To clear the system of air, you must install Maevsky cranes in the registers.

Advice: The system needs to be filled with non-freezing liquid because the garage heats up and down on a regular basis.

Garage stove in waste oil

The oil miracle-fucker may have burned through many garages, but its appeal hasn’t diminished. We are discussing the most typical design of a metal stove, which consists of two tanks joined by a bait (a perforated pipe). As long as the liquid fuel is free of water, it can operate on practically any kind. If not, fires start to occur because the heater starts to shoot flames through the burner’s holes.

As a point of reference. This unit has other drawbacks besides the fire hazard, such as Gary’s odor and its moderate "gluttony" consumption (roughly two liters of waste oil per hour).

You can’t ignore this furnace because of its affordability and simplicity, which account for its popularity as an exercise tool. The heater’s algorithm looks like this:

1. The spilled oil is poured into the lower tank and is set on fire using any flammable liquid.
2. After heating, the development evaporates and begins to burn.
3. The released pyrolysis gases are mixed in a fingertiper with secondary air and burned in the upper tank having a partition.
4. Combustion products leave the stove through the chimney.

The miracle tank is incredibly easy to assemble, following the drawing’s instructions:

A dropper for working out

The dosed oil supply to the combustion zone above a unique bowl is the basis for this safer and more efficient furnace’s operation. A steel fuel tube is brought to the bowl, which is welded inside the pipe, either from above or the side. Liquid fuel instantly evaporates and burns when it drips into a heated bowl, producing pyrolysis gas and heat. The latter is burned by feeding secondary air through a vertical pipe that is above the bowl and has burning holes or slots in it.

The majority of enthusiasts for waste oil heating favor using a fan to create a forced air supply for burning. Although the combustion process is difficult in this scenario, it is not required to do this if there is a chimney with good traction. As seen in the picture, dosage is controlled by a straightforward valve that is positioned in the fuel jet’s gap outside the stove:

Note: The fuel supply can be arranged through a special pump or by gravity by mounting the oil tank higher on the wall.

Bringing the burner through the wall to the stove on the side is the more appropriate way to do this. The development along the oil pipeline’s path heats up as it travels through the makeup and into the bowl. The potbelly stove’s body is reddened because the flame is concentrated in the area across from the burner’s holes. As a result, a lot of home masters like to use the dropper to create a boiler by covering its body with a water shirt. The following details about this garage stove can be found in the video:

Materials needed	Step-by-step instructions
Steel barrel or metal box	1. Cut an opening for the door. 2. Add a chimney hole on top.
Insulation materials (e.g., firebricks, clay)	3. Line the inside with insulation. 4. Secure insulation with mortar or clay.
Door hinges and handle	5. Attach hinges and handle to the door.
Grate or rack for wood	6. Install a grate or rack for wood inside.
Chimney pipe	7. Connect chimney pipe to the hole on top.

Constructing a wood stove for your garage can be a fulfilling endeavor, providing warmth and usefulness to your work area. You can design a cost-effective heating solution that meets your needs by taking a few simple precautions and basic steps. Building your own stove can be a rewarding project, regardless of your experience level with do-it-yourself projects.

Prioritizing safety above all else is vital during the construction process. In addition to adhering to any applicable building codes or regulations in your area, make sure the materials you choose can tolerate high temperatures. Furthermore, make sure you are working in an area with adequate ventilation and keep fire extinguishing supplies nearby in case of emergency. By following these safety measures, you can make sure that your stove not only works well but also presents the least amount of risk to you and your belongings.

Think about things like the size of your garage, how much heat you’ll need, and the materials you have on hand when designing your wood stove. Though there are many different designs available, simplicity is frequently essential, particularly for novice stove builders. Whether you want to build a simple barrel stove or a more intricate custom design, look for plans or tutorials that correspond with your skill level and desired features online.

It’s time to roll up your sleeves and get to work after you’ve assembled your supplies and created a plan. Take your time, double-checking dimensions and making sure that every component fits securely. Don’t be afraid to ask knowledgeable builders or members of online communities for advice if you run into any difficulties along the route. Recall that a project’s success depends on your ability to be patient and pay attention to detail.

Make sure you give your stove a thorough test after construction is finished before using it to heat your garage. Begin with a small fire and build it up gradually while keeping an eye on the stove’s operation and looking for any smoke or malfunctioning signs. After you’re happy with the outcome, you can work on projects in your garage while cozying up with your handmade stove.

To sum up, installing a wood stove in your garage can be a rewarding project that offers useful advantages as well as a sense of achievement. You can make a heating solution that improves your workspace and gives your do-it-yourself projects a unique touch by putting safety, careful design, and careful construction first. So gather your supplies, let your imagination run wild, and start building your own stove—you can be sure it will be a project well worth the trouble.

Video on the topic

Working, firewood, coal! Universal stove working on all types of fuel

Universal stove for working, firewood and everything that burns ! One day in the garage

Heat in the garage 2. Bake for any fuel!

How to make an oil stove in 5 minutes from a conventional stove

DIY

Heating for a penny. Homemade for the stove. DIY heating

Garage Bourgeois stove for working out on all types of fuel universal in waste oil