Connection of the wall-mounted gas boiler

Few things are more crucial to maintaining a warm and comfortable home than a dependable heating system. A wall-mounted gas boiler is the main component of many homes’ heating systems, giving them reliable heat and hot water all year round. For maximum efficiency and safety, knowing how to connect a wall-mounted gas boiler is essential, regardless of whether you’re installing a new boiler or updating your current setup.

A wall-mounted gas boiler requires more than just wall mounting to be installed. It necessitates exact connections, cautious planning, and adherence to safety guidelines. It’s crucial to determine the size of boiler needed for your home, its heating requirements, and any local regulations before beginning the installation process. Getting advice from a licensed heating engineer can help you decide which strategy is best for your house.

Getting the infrastructure in place is one of the first steps towards connecting a wall-mounted gas boiler. A gas supply line, water supply and return lines, electrical connections, and adequate exhaust gas ventilation are all included in this. You might need to add or modify these systems to make room for the new equipment, depending on how your house is laid out and where the boiler is located.

For the boiler to work well and last a long time, it must be installed correctly. This entails securing the unit to the wall with screws, attaching the gas and water lines, and setting up the electrical connections in accordance with the guidelines provided by the manufacturer. Paying close attention to details now can help later on avoid problems like leaks, malfunctions, or inefficient operation.

Testing and commissioning are required after the wall-mounted gas boiler is installed to make sure everything is operating as it should. This entails inspecting the area for gas and water leaks, confirming that all controls and safety features are operating as intended, and modifying the settings as necessary to attain peak efficiency. Giving homeowners comprehensive instructions on how to use and maintain their new heating system is also crucial.

Scheme of strapping wall-mounted two-circuit gas boiler

The gas boiler’s safety and efficiency are mostly dependent on how well it is connected to the heating system. There are multiple stages to this procedure, which is also known as strapping. Gas is a very dangerous fuel, so while some work should be done by trained gas service personnel, you can do a lot of the work yourself.

Installing a chimney, connecting to the gas and electric networks, and strapping in the heating system are all parts of connecting a wall-mounted gas boiler. We will attempt to describe each step in this article.

Strapping the gas boiler in the heating system

The first step is to connect the wall-mounted gas boiler to the heating system after it has been installed and the heating device has been mounted on the wall. Different piping schemes are used depending on whether a single- or double-circuit model is installed. We’ll use a wall-mounted, two-circuit gas boiler as an example to discuss the connection procedure.

Picture 1: A wall-mounted, two-circuit gas boiler’s connection diagram

As you are aware, the two-circuit boiler can provide hot water for domestic use in addition to heating. This can be achieved structurally by installing one or two independent heat exchangers. Although a two-circuit boiler only produces a small amount of hot water, it is enough for one or two distribution points, such as the kitchen faucet and shower.

Contemporary wall-mounted gas boilers are incredibly small and come equipped with all the essential components needed to run a forced-air heating system, including an expansion tank, safety group, and circulation pump. This is more than sufficient for small private country houses’ heating systems; however, if needed, an additional expansion tank or pump can be installed.

The bottom of every mounted two-circuit boiler has five spigots. They are connected to the following lines: the main gas supply, the DHW supply and return, and the heating supply and return lines. Typically, the gas inlet is painted yellow and situated in the center. Depending on the gas boiler model, the locations of the remaining lines can be placed in any order. Thus, it is essential to explain the function of each one in the operating instructions before turning on the piping.

Picture 2: Pipework layout for a wall-mounted, dual-circuit gas boiler

Metal or polypropylene pipes are used to strap the wall-mounted gas boiler. Generally speaking, the cross-section of DHW pipes is 1/2 inch, whereas that of heating pipes is 3/4 inch. "American" nuts are used to connect the boiler and heating system. Ball valves are installed on each line to make it simple to disassemble the gas boiler without draining the coolant and, in the event that it becomes necessary, to isolate the boiler from the heating system. All connections should be made using linen or sanitary FUM-tape to guarantee tightness.

Coarse filters must be installed in the DHW supply line and the heating return line. Shut-off valves also cut them off for ease of cleaning and flushing operations. Installing a fine-purification magnetic filter on the DHW supply is a common way to prolong the life of the secondary heat exchanger in a two-circuit boiler.

Returning to the contents table

Connecting the wall-mounted boiler to the power grid

The majority of gas boilers that are wall-mounted today have advanced automatics installed. It manages multiple operations, converting the heating boiler into a self-sufficient mini-boiler that essentially doesn’t need the owner’s assistance to operate. It goes without saying that the control unit and different sensors need to be connected to the power grid.

There are two types of wall-mounted boilers with two circuits: ones that plug in using a standard socket and others that require a cable to connect straight to the automated device. They must, in any event, be powered by the power supply via a separate automatic circuit breaker. Should you have procured a plug-equipped model, the dedicated gas boiler socket ought to be situated adjacent to it, but never beneath it. This is a safety measure to prevent a short circuit in the event of a coolant leak.

Picture 3: Setting up a voltage regulator for a boiler that is mounted on the wall

An earth connection is a must for the gas boiler. You can purchase a set of point grounding for this use. It is situated next to the house or in the basement and takes up a tiny space of roughly 0.25 m².

Take note! Grounding a wall-mounted gas boiler to a gas supply pipe or heating radiator is strictly prohibited. This is incredibly dangerous and a flagrant violation of the operating regulations for gas equipment.

Boiler automatic controls are highly susceptible to the quality of the power supply. Appliances fail quickly if the sinusoid at the input has an imperfect shape or insufficient level. In order to prolong the lifespan of the unit and avoid frequent malfunctions, gas boiler voltage stabilizers must be connected. An uninterruptible power supply should be bought extra to prevent the heating equipment from stopping in the event of a power outage.

Returning to the contents table

Choice of chimney for gas boiler

A chimney is required for any wall-mounted gas boiler. This can be a small horizontal chimney that can be led outside through the house’s wall or a traditional chimney, depending on the model.

Photo 4: Fitting a turbo boiler with a coaxial chimney

Air from the room where the heater is installed aids in the combustion process in two-circuit boilers with an open combustion chamber. These models are typically installed in boiler rooms with specialized equipment. In order to release the combustion products from gas boilers, they are connected to conventional ceramic or stainless steel flues.

External air is used by wall-mounted boilers that have a closed combustion chamber (turbo) in operation. One of the coaxial chimney’s channels serves as the device’s internal supply. Flue gases are released into the atmosphere via the second channel. Installing a coaxial chimney and connecting a gas boiler to it is a simple task that can be completed by one person.

Returning to the contents table

Connection to the gas mains

The only people who should connect the gas boiler to the gas pipeline are certified experts from the gas service or another company that is authorized to perform this kind of work. It is against the law to connect an independent structure to the gas main; in the best scenario, this could result in a hefty fine for the property owner, and in the worst scenario, disaster.

Speak with the gas utility as the first step in gasifying a property. You will receive individual technical specifications (TU) after submitting all required paperwork, which must be fulfilled in order to connect to the gas mains.

Once you have the TU in your possession, you can safely begin your search for a certified specialist who will design the gas pipeline and connect your heating boiler to it in compliance with regulatory authority requirements.

Attaching a wall-mounted boiler to the gas mains (photo 5)

There are two ways to gasify a building: aboveground and below ground. The above-ground portion is composed of steel pipes that enter the room directly at the location of the gas heating boiler, 1.5–2 m above the floor. The subterranean section is composed of corrosion-resistant polyethylene pipes.

Take note! When using multiple heating devices, the gas supply is handled independently for each one. Gas main laying within the room is not permitted at all.

When it comes to the installation process, it’s important to remember that all connections need to be sealed using paint or wax. Because of the low degree of connection tightness, using sealing tape or FUM is prohibited. To keep small debris and condensate out of the heating boiler, a gas filter needs to be installed on the cut-off tap. Steel pipes should be used to directly connect the gas boiler to the shut-off valve. Although the use of a special corrugated stainless steel hose is permitted, pipes are still recommended because they increase the cross-sectional area of the gas channel.

Watch this video to find out more about plumbing and connecting wall-mounted gas boilers:

Return to the contents table In summary

The longevity, effectiveness, and owner safety of a wall-mounted gas boiler are contingent upon its proper connection. We hope you found our brief overview of the key connection and piping stages to be helpful.

Installation of wall-mounted gas heating boilers – connection diagram on examples

Wall-mounted gas heating boilers are installed in apartments or private homes. Gas boilers are designed to heat the liquid coolant in autonomous heating structures. The wall-mounted gas boiler installation regulations must be strictly followed in order to guarantee the complete safety of the occupants, as these heating devices run on an explosive fuel.

First and foremost, owners of real estate should be aware that any work pertaining to the device’s connection to the gas mains and heating system must be done by experts strictly following the approved SNIPs.

Self-installation of wall-mounted gas heating boilers

Whether or not it’s possible for consumers to install a gas boiler themselves is a common question. Create a project and coordinate it with the local supervisory authorities prior to installing the gas heating system (specifically, "Installation of a gas boiler with your own hands – do it right").

The boiler’s specifications, location, and an explanation of the overall heating system’s operation are all listed in the project documentation. A portion of the installation work can be completed by hand only after its approval. But not every producer of gas heating equipment permits independent installation of their heat units:

• companies Ariston, Viessmann, Bosch and a number of others oblige buyers to perform installation of the wall-mounted gas boiler exclusively by employees of certified centers;
• Some manufacturers, such as BAXI, Ferroli, Electrolux more loyal to this issue, do not prohibit the unauthorized installation of wall-mounted appliances. But in any case, for commissioning activities in the arrangement of heating construction will need the services of specialists who are authorized to connect gas and electrical equipment.

Verify that the manufacturer approves of this work before moving forward with the boiler’s independent installation.

Connection diagram of the wall-mounted gas boiler

It is best to place mounted heat generators in a different room. It is frequently called a boiler room or furnace room. The type of combustion chamber boiler that is intended to be purchased will determine the requirements for this room (for more information, see "Connection diagram of gas heating boiler on examples").

Combustion chamber of the open type. A typical stove operates on a similar principle, which is as follows: the device draws air from the room through a natural draught, and the exhaust gases are subsequently expelled through the chimney.

A specific amount of air must be present in the room for gas boilers to function properly. If not, the gas will not burn all the way through and harmful compounds will form, endangering public health. A minimum of 0.5 "square" feet of space, a window facing the street, and a maintenance area are required when installing wall-mounted gas heating boilers. The walls of the boiler room need to be constructed from fire-resistant materials.

The connected equipment’s power determines the furnace room’s volume:

• for boiler output not exceeding 30 kW – 8 m³;
• for 30-60 kW it is enough 13-14 m³;
• for capacities up to 200 kW – 15 m³ and more.

Combustion chamber of the closed variety. A coaxial chimney, which consists of two pipes, is included with these boilers. The outer pipe is used for air intake straight from the street, and the inner pipe is required to remove combustion products. A connection to the power grid is necessary when installing heat units with closed combustion chambers in order to power the fan that circulates air through the chimney. This is typically provided by a gas boiler’s chimney device.

Since closed combustion chamber appliances are thought to be safer and greener, they can be installed even in areas where people don’t sleep, like the kitchen, bathroom, pantry, and other rooms. There are no strict guidelines for the chimney’s parameters because automation oversees the removal of combustion waste. Wall-mounted gas heating boilers with a closed combustion chamber are permitted in multi-story building apartments.

Rules of installation of the wall-mounted gas boiler

The type of combustion chamber and the number of circuits (one or two, depending on whether hot water supply is needed in addition to heating or just heating) will determine how the wall-mounted gas appliance is installed and connected in the future. See also: "Gas heating boiler installation guidelines – installation and connection instructions." The installation of single-circuit boilers is the subject of this article.

Mounting on the wall is stage one. The hinged gas boiler in the picture is fixed to a unique bracket that is part of the set along with the appliance. However, depending on the type of wall it will be placed on, the fasteners are not always appropriate and frequently need to be bought separately. In actuality, the bracket needs to support the device’s weight and guarantee that it is perfectly level. See also: "Linking the heating system to a two-circuit gas boiler."

The surface of the wall, which is behind the thermal unit, must be protected with a non-combustible material. The installation height of the wall-mounted gas boiler assumes that the suspension of the lower part of the heat unit will be at a distance of at least 80 centimeters from the floor, and the gap between the wall and the back surface will be 5 centimeters.
Step two – connection of the heating main pipes. To the boiler will need to connect the number of pipes, depending on what kind of system is mounted – one-pipe or two-pipe. Before making the connection, the plugs must be removed from the unit"s socket. At the inlet of the return, experts advise installing a filter to prevent debris and dirt from the heating main from getting into the boiler.

When using water as a heat carrier, the quality—more specifically, its hardness—is crucial. Cleaning tools like polyphosphate dosers can help address this weakness; if not, the wall-mounted device will soon stop functioning.

The heating unit is connected to the gas network in stage three. Regulations pertaining to the connection of wall-mounted gas boilers state that only qualified professionals with the necessary licenses should carry out this portion of the installation.

The following components will need to be installed in order to complete the work:

• ball valve (gas), which is mounted at the inlet of the unit;
• gas meter and leakage sensor – they are cut into the mains before the device;
• thermal shut-off valve (according to fire safety regulations). When the temperature near the wall-mounted heating unit rises to a critical value, for example, in case of fire, this device will automatically cut off the gas supply.

Connecting to the main power supply is the fourth step. Only gas boilers with fans and automation systems that are intended for waste removal require a power supply. Typically, set up an inclusion scheme with three wires, and grounding is required. To prevent voltage spikes, it is preferable to use a voltage stabilizer when connecting the wall-mounted boiler to the power grid.

The fifth stage involves setting up the chimney pipe outlet. An individual chimney connection is necessary for atmospheric gas boilers. The wall-mounted gas boiler’s connection scheme stipulates that an iron pipe with a specific cross-section is used to connect the device to the chimney. This pipe is resistant to high temperatures, mechanical wear and tear, and the influence of combustion products.

Make sure the chimney is clear of any debris and soot residue before moving on to the connection.

Follow these guidelines when installing the pipe segment that connects the boiler to the chimney:

• The vertical part located at the outlet of the appliance should be at least two diameters long to the point of turning;
• Then the pipe should be positioned with a slope towards the unit;
• the section to be connected to the chimney should be as short as possible.

The issue of exhausting the combustion products is resolved more readily in boilers with closed chambers. They can be linked to a communal chimney or directly connected to the street via a coaxial pipe that is run through the wall. Since the built-in fan creates the draught, there is no need to check the height of the chimney suspension.

Filling with water is step six. Open the valve, which is often found at the bottom of the mounted boiler, prior to the test run. Pumped in water is brought up to two atmospheres of pressure. The air inside the chimney needs to be released, so proceed cautiously. A tightness check should be performed on the heating construction.

First start-up

A qualified specialist should perform the wall-mounted gas boiler’s initial startup. He will check the system’s functionality and make all the necessary adjustments (for further details, see "How to start the gas boiler for the first time").

Questions about the use of heating gas equipment can be directed towards a professional during the commissioning process.

A certificate is signed following the completion of the commissioning work.

Thus, it is impossible to characterize the installation of wall-mounted gas boilers as simple. It calls for the necessary plumbing and construction industry experience. There are times when it is impossible to proceed without the involvement of specialists. However, you will be able to save a good amount of money if you take a few independent actions. In the video, there are examples of installing wall-mounted gas heating boilers:

Installation of a wall-mounted gas boiler: installation with your own hands in compliance with the norms

The house ought to be warm by definition. It can be given in a number of methods. The cautious owner, however, aims to accomplish this as cheaply and effectively as feasible. One of these alternatives is to install a gas boiler that is wall-mounted. And it makes perfect sense—gas heating is incredibly profitable, and installing and operating the equipment is not too difficult. Think through every detail involved in connecting such a system.

Wall-mounted gas boiler: how it works

The heater’s installation and connection are contingent upon its kind. Consequently, it is essential to comprehend the specifics of the device’s operation as well as which of its variants needs to be handled.

Every wall-mounted gas boiler is a small appliance with a 42 kW maximum capacity.

Wall-mounted gas boilers are strong, small appliances that heat and heat water for a space.

The system’s primary components are as follows:

• Gas burner. Supplies gas into the chamber where the combustion process takes place. With the help of nozzles fuel is distributed as evenly as possible. Modern modulating burners can maintain a set temperature and regulate the flame strength.
• Heat exchanger, through which the coolant moves. Best efficiency of a copper appliance. Condensing boilers may have two of these elements.
• Expansion tank. Designed to compensate for excess water resulting from heating.
• Circulation pump. Powerful models can have two such elements.
• Boiler automatics or a system of devices whose task is to maintain the set temperature in the heated room. Can include electric or non-volatile appliances.
• Devices that monitor and regulate the boiler operation.
• Fan. Used only in turbo models.
• Safety system. Stops the boiler operation in case of dangerous situations.

Additionally, 90% of boiler malfunctions can be identified by the self-diagnostic systems included in modern models. The diagnostic breakdown number is displayed on the display, and the service technician quickly fixes it.

The diagram of a wall-mounted, two-circuit gas boiler with a closed combustion chamber is depicted in the picture (+)

Varieties of wall-mounted devices

Gas heating units are separated into two categories based on their intended use:

• Single-circuit. Intended only for heating. They are connected to the heating circuit and heat the coolant. Organization of hot water supply in this case is carried out by installing an electric or gas water heater of any type.
• Dual-circuit. Heat the room and provide hot water supply. An additional circuit for heating water is built into the boiler. Technological feature of the device is the impossibility of simultaneous heating of water and heating of the room.

The heating of water is the two-circuit unit’s primary function; the heating process ends at this point. Given that water can be heated rapidly, the building is effectively heated by the boiler.

Purchasing a two-circuit boiler is preferable if the gas unit’s functions include both hot water supply and heating medium heating. One or two heat exchangers are included with them. When two are present, they can serve two circuits at once (+)

Each device is categorized into one of two groups based on the fuel combustion method:

Devices with an open combustion chamber

Another name for these gadgets is natural draught heaters. They remove the oxygen from the room where the unit is situated, which is necessary for combustion. They require a conventional type of chimney in order to remove combustion products. Therefore, having adequate ventilation set up is a must for installing a boiler of this kind.

A high-performance supply ventilation system must be set up if the heater is placed in the living area. An isolated space known as the "furniture room" is thought to be the best location for the installation of a heater with an open firebox. Natural ventilation systems are very popular because they are inexpensive and energy-efficient.

A schematic representation of open and closed burner boilers is shown in the figure.

Appliances with a closed combustion chamber

There is a closed combustion chamber on turbine devices. They take air from the street, since the combustion process cannot occur without it. The appliances have coaxial-style smoke vents for this reason. This kind of chimney is constructed as a pattern consisting of two pipes, with one inside the other. Through an internal pipe, the combustion products are released to the outside.

Meanwhile, through the opening between the two pipes, street air enters in the opposite direction. It is evident that closed furnace boilers have no effect on the air composition within the space, meaning that they can be installed even in living rooms. In this situation, setting up a coaxial chimney system—which is more expensive and requires more intricate installation than a separate, conventional chimney outlet—is required.

In connecting a wall-mounted gas boiler to your home, the key lies in ensuring safety, efficiency, and effectiveness. Proper installation is crucial to guaranteeing optimal performance and longevity of your heating system. Understanding the process involves assessing your home"s heating needs, selecting the appropriate boiler size, and positioning it correctly. Additionally, it"s essential to adhere to local building codes and regulations, ensuring compliance and safety standards are met. Proper ventilation and gas supply are paramount for safe operation. Hiring a qualified professional for installation is highly recommended to avoid potential hazards and ensure a seamless connection. Regular maintenance and inspections further ensure the boiler"s functionality and safety, providing reliable heating for your home throughout the seasons.

Self-installation: is it possible?

Even the simplest modifications, like installing a wall-mounted gas boiler, can be done by hand. Single-circuit appliances with an open combustion chamber are one example. The heating system, gas, and chimney outlet must be connected in order for them to be installed. Nonetheless, some boiler manufacturers specify that only professionals should perform the installation in the technical documentation for their products.

The process of installing and connecting a gas boiler is a complex and responsible task. Many heating equipment manufacturers insist that it be done by experts.

Even the most basic models cannot be installed independently in this situation. Therefore, it is essential to confirm with the manufacturer that the equipment can be installed independently before making a purchase if that is the plan. Only a specialist with a specific permit should verify that the device was installed correctly and that it was connected to the gas mains.

An operating permit for the installed equipment must also be issued by the gas service representative. In the absence of it, the owner of an appliance that was installed and commissioned independently faces harsh consequences. Therefore, the only tasks that can be completed without the assistance of specialists are connecting the device to the water supply and the heating system. And you should only try this if you have some prior experience.

Gas boilers mounted on walls are used in forced-type autonomous heating circuits where the coolant circulates naturally (+).

Where to start the installation?

First things first, the paperwork needed for installation needs to be ready. Beginning with the premises’ gasification must be the first step. Only with a gas main connected to it can it be started. Subsequently, the proprietor applies to the appropriate agencies, indicating how much gas he uses annually or monthly. The gas main that approaches the premises must have a meter installed in the event that the application is approved.

The installation project must be developed and approved before any equipment can be installed. Every requirement outlined in the permit must be properly followed.

The authorization documents and technical specifications that the owner receives in person serve as the foundation for developing the equipment connection project. The latter covers all requirements for equipment installation as well as the configuration of the gas pipes running from the heater to the mains connection point. The gas service has to approve the developed project.

A certificate of conformance and technical passport of the purchased equipment, the conclusion of the expert service on its compliance with all safety requirements, and usage instructions are provided by the project owner along with the room where the boiler will be installed. Installing the heater is only possible once the project has been approved. In this situation, it is imperative that you meet every requirement outlined in the project documentation.

What should be the room for the boiler?

Gas appliances are categorized as equipment that poses a risk of explosion and fire. The room where it will be installed must therefore meet certain requirements. It must have natural light first and foremost. In this instance, there should be at least 0.03 square meters of window opening—that is, just glazing—for every cubic meter of space. There must be a vent installed in the window.

The gas boiler installation wall needs to be finished with non-combustible materials.

The availability of supply ventilation, which can alter the room’s air volume three times in an hour, is another requirement. This will reduce the amount of gas in the space. Additionally, the volume of the room where the boiler will be installed affects the boiler’s capacity. Boiler rooms with a capacity of 7.5 cu. ft can accommodate equipment up to 30 kW in size.

Furnaces with 30 to 60 kW of power require a furnace room that is no more than 13.5 cubic meters in volume. m and higher. The kitchen is typically where the heater is installed in apartments. If all of SNiPs’ requirements are satisfied, then it is feasible. A crucial detail: in this instance, the total heat output in the kitchen from all of the heating appliances should not exceed 150 kW.

SP-41-104-2000 and SNiP 42-01-2002 govern the requirements for installing gas heating equipment. Adherence to the installation guidelines ensures secure functioning.

In order to increase air exchange in the kitchen, the installation guidelines for wall-mounted gas boilers stipulate that the door’s opening must be at least 0.02 square meters in size and be covered with a grille. Experts advise against installing equipment in apartment buildings unless it has a closed furnace and a coaxial chimney. It is not permitted to install more than one heating device in kitchens with a volume of 7.5 cubic meters or less.

It is advised that gas boilers in private homes be placed in a room divided from the living areas by sturdy, fireproof walls. The materials used in the room should ideally have a minimum 45-minute fire resistance time limit. It is ideal for the building’s design to impede the flames from quickly spreading to the living areas.

One of the options for connecting the wall-mounted gas boiler is depicted in the photo.

Only a solid base can be used to mount the gas boiler. Plywood or plasterboard partitions are inappropriate for this use. Materials that are fireproof must be used to finish the wall where the heater will be installed. A non-combustible substrate is installed beneath the boiler if this isn’t the case. The appliance must be at least 0.5 meters from the ceiling or walls and 0.8 meters from the floor to the supporting structures.

Step	Description
1	Choose a suitable location on an external wall for the boiler installation.
2	Ensure the wall is strong enough to support the weight of the boiler.
3	Drill holes in the wall for piping and ventilation.
4	Mount the bracket securely on the wall.
5	Connect the gas supply line to the boiler.
6	Attach the flue pipe to the boiler for venting.
7	Connect the water pipes for both hot water and heating.
8	Check all connections for leaks.
9	Test the boiler to ensure it"s working properly.

One of the most important steps toward providing your home with effective insulation and heating is installing a wall-mounted gas boiler. Choosing a gas boiler means that you’re making an economical and dependable choice for heating your home in the winter.

The space-saving nature of a wall-mounted gas boiler is one of its main benefits. A wall-mounted boiler can be easily mounted on a wall, freeing up valuable floor space, in contrast to traditional boilers, which need to be installed in a separate room or large space.

Additionally, when done correctly by a trained expert, connecting a wall-mounted gas boiler is a fairly simple procedure. In order to make sure that everything is correctly connected and operating effectively, it entails connecting the boiler to the gas supply, water supply, and heating system.

Compared to other heating systems, a wall-mounted gas boiler can drastically lower energy costs and provide reliable heating performance once installed. By installing the right insulation, you can reduce heat loss and increase boiler efficiency, keeping your house cozy and warm all year round.

To sum up, installing a wall-mounted gas boiler is a useful and efficient way to heat and insulate your house. You and your family can enjoy dependable heating, reduce energy expenses, and improve the comfort of your home by purchasing a gas boiler and making sure it is connected correctly.

Video on the topic

Boiler connection

How to correctly connect the wall-mounted gas boiler

Strapping and installation of the gas boiler | What materials should be used for strapping?

Gas boiler connection diagram. Connecting a wall-mounted boiler

Strapping of a wall-mounted boiler (under polypropylene)

Installation of a wall-mounted gas boiler. Part 2.