Close the pipes in the toilet with plastic panels – do it right

To keep your home comfortable and cut down on energy expenses, make sure it is adequately insulated. The piping system is one component of insulation that is frequently disregarded, especially in spaces like bathrooms where exposed pipes can result in heat loss. This post will discuss the advantages of using plastic panels to enclose toilet pipes and offer a detailed tutorial on how to do it properly.

In addition to being unsightly, exposed plumbing in bathrooms can cause heat loss, particularly in colder climates. You may successfully trap heat and stop cold drafts by covering these pipes with plastic panels, which will eventually increase the overall warmth and comfort of your house. Furthermore, insulating your pipes can lessen the chance of expensive damage and repairs by keeping them from freezing during the winter.

Getting all the materials needed is essential before beginning the installation process. To keep the plastic panels in place, you’ll need fasteners or adhesive made especially for enclosing pipes. To make sure you buy panels that fit snugly around the pipes, it’s also a good idea to measure the pipes’ diameter and length. Accurate measurement taken in advance will facilitate installation and guarantee a good fit.

When your supplies are prepared, it’s time to start the installation procedure. To ensure a perfect bond between the adhesive and the pipes, start by giving their surface a thorough cleaning to get rid of any dirt or debris. The plastic panels should then be adhered to the back with adhesive, or fastened around the pipes using fasteners. Press firmly to guarantee a tight seal, and before moving further, give the adhesive enough time to dry.

Make careful to check that all joints and connections are properly covered and sealed as you make your way around the pipes. All gaps must be properly sealed to keep heat from escaping and to optimize the insulating properties of the plastic panels. After every panel is firmly in position, take a moment to check the installation to see if there are any gaps or areas that might require more care.

In conclusion, installing plastic panels around toilet pipes is an easy yet efficient method to lower energy expenses and increase your home’s insulation. You can enjoy a warmer, cozier living area and lower utility bills by following the instructions in this article and taking the time to ensure a proper installation. Don’t let the insulation in your bathroom pipes go unnoticed; act now to enhance it and enjoy the benefits for years to come.

Requirements for materials

The restroom is a space with a unique microclimate. Thus, choose the material before hiding the pipes in the toilet.

It must fulfill crucial requirements like:

1. Moisture resistance. There is constant condensation in the toilet. Water droplets settle on the surfaces. Over time, unstable products begin to soak, fungus and mold appear. Therefore, the wiring should be sealed with products that are resistant to high humidity.
2. Durability. Constantly need access to meters and ball valves. Special hatches are installed for this purpose – with a fragile structure they will not withstand them.
3. Aesthetics. Another important criterion. It is better if the product will be combined with the overall finish of the toilet.

Close the pipes in the toilet with plastic panels – instructions

Using plastic panels to conceal the toilet’s pipes is not a difficult task. The entire process won’t require a lot of time. However, in this instance, the room’s appearance drastically changes. Water and sewer pipes are functional components, and this is no secret. They detract greatly from the interior’s overall design and appear strange against the stunning tiles. For this reason, a lot of people cover their pipes with different materials; plastic panels are the most widely used.

There are multiple methods for rendering the drainage and plumbing system undetectable. The most typical is the fake wall. There are additional, more intricate choices. The grooves that are carved into the walls are one of them. Shutters that roll are the next technique.

Pipe covers are frequently made of plastic or plasterboard. Furthermore, experts classify plastic as more useful. Ultimately, it is easily removable from the frame for maintenance purposes. Its extreme resistance to moisture—it has no fear of it—is yet another significant benefit.

We will include the following elements in addition to the previously listed advantages:

• short installation time;
• low weight of the structure;
• increased noise insulation level;
• variety of options allows you to choose a material for any interior solution;
• affordable price;
• long time of use.

They are made from polyvinyl chloride, sometimes referred to as lathing or PVC panels. Their cellular structure helps to identify them in the cross section.

Typically, the lathing’s thickness doesn’t go above one centimeter. It ranges in width from 15 to 50 cm. Three meters is the equivalent of the standard length. A common size range is 20–37 cm.

A wide variety of colors makes selecting a specific design solution simple.

Moldings of various shapes are used to ornamentally decorate the lathing fastening locations around the perimeter, as well as in the areas of joints and corners. Because they are painted white, they blend in flawlessly with any color scheme.

The standard tools for finishing metal and wood will work just fine for installing wagons; a few more tools are required, as you’ll see below.

The panels can be formed into any shape by heating them. They have strong welding and glue joining them. They can be applied to a wall at any inclination angle. The presence of the pipeline won’t be noticeable to the surrounding area if the box is constructed and lined correctly.

As was previously mentioned, a wooden bar is not a wise choice in a room like a bathroom or toilet. due to the humidity in the space, which will harm the wood. The necessary protection is not obtained, even with protective mortars.

A wide range of galvanized steel profiles and fasteners are available from modern production. Take a unique profile in order to conceal the pipes in the restroom or toilet. Three to four meters is its typical length. The transverse measurements are 20 x 20 mm. However, they might be bigger.

Features of work

Covering the pipes with plastic wagons appears to be a simple task at first. However, many people often lack a clear understanding of this work when they first begin. Specifically:

• Before hiding the pipes, it is necessary to check their condition. It may be that they need to be replaced. And such a problem should be solved before you start cladding. Because an emergency situation can occur after the entire structure is mounted, and then the structure will have to be dismantled. Old steel and cast iron pipes require special inspection. These are highly durable and reliable building materials, but a careful inspection can reveal cracks and chips, which soon grow into big problems.
• After the issue of pipes is finally solved, it is necessary to determine the exact shape of the structure that will cover them.

Space is not occupied by pipes. Furthermore, the location of the pipeline determines the overall concealing structure’s size. Ultimately, the riser might be in the center, or it might be in the corner. Horizontally oriented plumbing is typically found near the floor.

• Do not forget about valves, meters, etc., access hatches must be made to access them.

• If the pipes pass in niches, then such places are advised to cover with a false wall, or make an L-shaped structure.
• Horizontally located pipes must be covered with a rectangular sill. In the area of the sink, the threshold should be raised to its height, and the empty space should be used to arrange shelves.

You can take care of the required tools and building materials once all these moments have been planned.

Paneling requires the following tools:

1. construction level;
2. knife (for installation actions);
3. Profile (starter and guide);
4. screwdriver and screwdriver;
5. panels.

It is advised to make a quick sketch before beginning work in which the future hiding structure’s measurements are recorded. Determine the materials needed to fix the wagons at this point as well.

It should be remembered that glue is not the ideal solution in this case because the building may need to be disassembled at any time. It is advantageous to utilize self-tapping screws from this perspective.

Application of plastic panels

There will be a false wall to build before the toilet’s pipes can be covered with plastic panels. These are the directions for setting it up:

• making markings in the area of the ceiling and floor. Fixing guide profiles to the floor and posts on the walls.

• In the corners of the structure fasten the mullion profiles;
• With a half-meter indentation mount profiles located transversely, otherwise the building will not be rigid:

• frame cladding.

The work is explained in detail in the video below. This is a detailed description of the procedure, so even a novice master can handle this task.

You can close the ugly pipeline and decorate the space beautifully by carefully reading the information that has been provided.

Peculiarities of marking

The floor is first used to draw the contour. You must verify the angle based on how accurately you observed the corners. The contour can be transferred to the ceiling after accuracy has been verified.

The rack profile is mounted on the box’s corners. A construction level should be used to check its vertical position. At the same time, mark the projection of the floor’s contour on the ceiling with a point.

Crucial! to ensure that the mark on the floor and the ceiling exactly match. It is important to determine the floor’s precise horizontal location before marking it.

Installing the frame

You cannot omit the foundation’s construction in order to cover the toilet’s pipes with plastic panels. This design is required for cladding with other materials as well as when working with wagons.

It should be noted right away that experts recommend galvanized metal profile as the best fastening for plastic wagons. It shields the metal from corrosive formations and offers just the correct amount of rigidity.

Many choose to use regular wooden bars in place of the system in order to shut it down. However, since the wood needs to be treated with an antiseptic, this is not thought to be the best option. Additionally, fire safety significantly declines in this version.

A plastic batten must be ready in order to seal the toilet’s pipes. The panels in this variation need to be mounted using specific clips. However, a significant drawback of this type of frame is its lack of rigidity.

Fixing the profiles to the floor is the first step in building the frame. The uprights are positioned in a vertical orientation behind them. Cross ribs are positioned very last. Self-tapping screws are used to secure the profiles to one another.

When working, it’s important to be aware of how big the space is between the frame’s ribs. The distance between the plastic panels is roughly 60 to 80 cm when arranged from bottom to top. If they cross each other, you might need to install an extra post.

Crucial! Remember that there should be a window left close to the revision and fittings. In order to access the system, it is required. It is advisable to consider the window’s location when building the frame.

Cladding the structure with panels

The panels on the mounted base must be strengthened in order to cover the sewer pipe.

At the wall, a starter molding is put in. Self-tapping screws are used to fasten it to the profile. The following plate overlaps this fastening, which is done through the shelf. The self-tapping screw’s flat on the plastic sheeting will be hidden in this manner.

The next plate’s projecting portion is inserted into the groove of the preceding plate and pushed in until it stops. Self-tapping screws hold the panel’s free portion in place. Every wall in the ready base is covered using this principle. There is molding on the outside corner. The joints between the structure and the floor and ceiling are embellished in accordance with this principle. Remember that the frame shouldn’t be closed "on the blind." A hole for ventilation needs to be made in the upper side of the structure, and it needs to be at least 5 cm in diameter.

The issue of how to shut off the pipes is now regarded as solved. After closely watching the offered videos, you can complete this task quickly.

Plastic box

A plastic box can be used to cover up the sewer. This is a typical method of concealment.

There are multiple steps in the process:

1. Testing. Before starting work, it is necessary to check the operation of all devices, as well as the condition of assemblies and connections.
2. Sanitizing. Antiseptics are used to fight fungi. Before closing the sewer, the wall is treated with a special agent. The toilet is a small enclosed room. Ventilation in it is poor. Therefore, the risk of fungal spores is very high.
3. It is necessary to make a purlin. It can be on all the walls where the box will be installed, or only in those places where the communications run. A purlin is made from a metal profile or wooden bars.
4. Installation of the box. It does not take long to cover the necessary area with plastic. Each section should be fixed strictly in its place. Small nails will suffice as fasteners. There are small gaps in the corners and at the joints. Hiding them with inserts or decorative strips.

Be mindful! Cutting a hatch out of plastic is not a practical solution. Getting one already made is preferable. It needs to be presentable because it will be seen. The appliances inside the box can be fully accessed with a model that is large enough.

Box in the toilet from PVC panels: advantages and disadvantages

PVC panel box: an extremely common method of concealing communications. They are reasonably priced. In addition, the color palette is adequate to allow the box to blend in with the room’s interior design.

They are well-liked because of the following traits:

1. They are easy to cover communications.
2. They are quite strong and lightweight.
3. Do not weigh down the interior.
4. Plastic is resistant to moisture.
5. No mold problems with regular maintenance.

Installing a sewer pipe in a PVC box is less expensive than doing so with alternative materials.

How to cover pipes with plasterboard?

More finishing is needed for this material. And your creativity is unrestricted by that. Plasterboard has outstanding qualities in all other respects. Wiring can be easily hidden with it. It is simple to assemble and disassemble.

Plumbing hatch insertion is far simpler. The material is fireproof, moisture resistant, and eco-friendly. Tiles are used to finish the surface further. The riser pipe is best covered in this manner. Tile is simple to maintain clean.

Gypsum cardboard sheets are used to make a variety of box types. Every variation has unique installation requirements. Communication is therefore conducted behind the toilet bowl using the blind wall.

The sheets are mounted all the way around the opening to seal it off. The frame is fastened first with dowels and self-tapping screws, followed by the purlins. Sheets of gypsum plasterboard are the last step.

For restrooms where the communications are tucked away in a corner or take up only a portion of the wall, a plasterboard square box is utilized. The metal profile is fastened to the ceiling, walls, and floor in order to conceal the wiring. The vertical guides are then put in place. A window made of metal profile is present prior to the door being installed. We now cover the toilet system with a plasterboard sheet.

If the plumbing is located on the lower level, it is hidden by a multilevel box. The false wall’s oblique shape conserves empty space. The walls, ceiling, and floor are all covered in profiles. A horizontal framework is then created. Sheets should now be covering the profile.

Detailed instructions for using drywall to line the toilet’s pipes:

1. On the floor, walls and ceiling to make markings for the future frame. On them to fix the overhangs. On them the profiles will be installed. Start caulking from the floor, slowly moving to the walls and ceiling. The next step is to install the outriggers. The canopies and profiles are fastened with self-tapping screws.
2. Now the framework is ready. It"s time to start installing drywall. Sheets are attached to the profile strips. Fixing with self-tapping screws every 20 cm.
3. Close the gaps between the sheets with reinforcing mesh or putty. Mesh will protect the joints from cracking.
4. Cladding is ready. You need to make several openings in the sheets and install manholes in them.
5. It is additionally treated with putty and the final facing is done.

In the quest to keep your home warm and energy-efficient, ensuring proper insulation is crucial. When it comes to the often overlooked aspect of insulating pipes, especially those in the toilet area, using plastic panels can be a game-changer. By effectively sealing off these pipes with plastic panels, you can prevent heat loss, reduce the risk of freezing during cold weather, and ultimately save on energy bills. However, it"s essential to do it right to reap these benefits fully. From choosing the right materials to proper installation techniques, attention to detail is key. By following the correct procedures, you not only enhance your home"s energy efficiency but also contribute to a more comfortable living environment. So, when it comes to insulating toilet pipes with plastic panels, doing it correctly can make a significant difference in your home"s overall insulation and energy efficiency.

Blinds or roller shutters

A workable method of hiding communications. However, it also has drawbacks in addition to benefits. We will go over each nuance in greater detail below.

Decorative blinds

In the bathroom, vertical or horizontal blinds cover a lot of pipes. They’ll take on the appearance of curtains that are easily blocked from view. They can be easily rolled up to provide access to the pipes when needed.

The following are roller shutters’ primary benefits:

• space saving;
• easy and quick installation without construction debris;
• work is carried out very quickly;
• sturdiness and durability;
• affordable price;
• A large selection of colors and patterns;
• if one lamella is damaged, it is not difficult to replace it, there is no need to throw out the entire structure.

Roller shutters

Covering the space with roller shutters is more sensible. Their structure is more dependable and long-lasting. However, they occupy a lot more room than blinds. Particular consideration should be given to automatic roller shutters. They are practical to use and simple to close. There is a remote control included.

Using shutters to conceal the pipe will be more expensive and time-consuming. The panels can be patterned with almost any design. Printing photos is how it’s done. We can conceal household trinkets behind the panel. It’s sufficient to add a few shelves with nails.

Additionally, there are drawbacks to roller shutters. They have a unique frame attached to them. It is positioned all the way around the opening’s edge. Ventilation is necessary for pipes. As a result, the design cannot be fully covered because it does not reach the ceiling.

The upper portion will require additional materials to complete. It will be essential to consider the lifting mechanism’s features. The bottom is the same. It is not possible to hide until the very end due to the plumbing, which keeps the rollers from being fully lowered. The second portion of the canvas is used to conceal the bottom portion.

false wall

Cover the whole rear wall if there are metering and communications devices on the aircraft. Plasterboard (or plastic) and a profile make up the false wall.

But first, you must decide where to put the hatch before covering the pipes. It is simpler to install a special door in plastic panels. sold pre-made replicas.

However, there are additional choices when using tile-faced drywall:

1. The first is a hatch made of metal or plastic with hinged doors.
2. The second is a special hatch, on the doors of which the tile is glued. It is bought in advance. Tiles are placed so that its seams fully coincide with the seams of the wall tile.
3. The third option is a homemade hatch. It will cost less. A window is made in the false wall. Then measurements are made. According to them, a frame of metal is made. A cut sheet of plasterboard is attached to it. The tiles are glued on it.

Benefits	How to Do It
1. Insulation	Measure the length and width of the pipes. Cut plastic panels to fit and wrap them around the pipes. Use duct tape to secure the panels in place.
2. Prevention of Condensation	Insulating pipes prevents condensation buildup, reducing the risk of mold and water damage.

Maintaining your home’s pipes and insulation properly is essential for preventing future damage and increasing energy efficiency. Placing plastic panels over the pipes in your toilet can be a smart solution, but in order to fully benefit from the installation, it must be done correctly.

First and foremost, it’s important to choose the appropriate materials. Choose premium plastic panels that are intended to act as insulation. These panels ought to be strong, resistant to moisture, and able to effectively seal off the pipes to stop heat loss.

Installing things correctly is equally crucial. To ensure that the panels fit your pipes precisely, take careful measurements and cut them accordingly. Any cracks or loose fittings could reduce the insulating value, wasting energy and possibly causing problems later on.

Before putting in the plastic panels, take note of any existing insulation and plumbing parts that might need to be changed or removed. The longevity and efficiency of the panels will be enhanced by providing a smooth, clean surface for them to adhere to.

Following installation, regular maintenance is crucial for the panels. Check the insulation from time to time for any indications of wear, damage, or gaps. Promptly addressing any issues will help preserve maximum energy efficiency and avoid future expensive repairs.

To sum up, installing plastic panels to seal the pipes in your toilet can be a workable way to increase energy efficiency and reduce heat loss. You can optimize the advantages of this insulation technique and take pleasure in a more cozy and economical living space by choosing high-quality materials, making sure the installation is done correctly, and performing routine maintenance.

Video on the topic

Box to the toilet

How to cover the pipes in the toilet. Metal box

How to make a box of panels and close the sewer and water pipes, plumbing hatches.

How to make a PVC PANEL BOX in 45 minutes ? See here.

Finishing the toilet with plastic panels. HOW NOT TO DO!

How to close the pipes in the toilet so that they would be quickly accessible. Apartment renovation.

How to close the pipes in the toilet for finishing with plastic and tiles. Box for pipes in 2 hours with your own hands!

How to cover pipes, how to make a box from plastic laminated panels